GREAT PLANES Ultra Sport 40 Plus страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 62

background image

❏

1. Retractable Mains/Fixed Tailwheel. Cut out the root

rib so that the retract servo fits between the wing dowels.
Place the servo between the dowels as shown above. Both
a Hobbico CS-63 retract servo (HCAM0160) and a Futaba
compact retract servo (FUTM0670) fit well in this location.

❏

2. Retractable Mains/Fixed Tailwheel. With the servo in

place, drill a 1/16" [1.6mm] hole through the servo mounting
holes into the dowels. Remove the servo and wick some thin
CA into the holes.

❏

3. Retractable Mains/Fixed Tailwheel. Install the retract

servo in place with the hardware supplied by the
manufacturer. Remove the servo’s output shaft.

❏

4. Retractable Mains/Fixed Tailwheel. The retract leg

should have a total length of 3-1/2" [89mm]. Mark the leg of
your retracts at that distance when the retract is fully
extended and cut it with a high speed rotary tool such as a
Dremel Moto-Tool.

❏

5. Retractable Mains/Fixed Tailwheel. Locate the

leftover 2-56" rods from the pushrods. Cut and bend the wire
as indicated in the retract wire template on page 8. The
template on the top is for the right retract and the template
at the bottom is for the left retract.

42

«
...
40
41
42
43
44
...
»

Содержание Ultra Sport 40 Plus































































Отзывы:

Нет отзывов

Похожие инструкции для Ultra Sport 40 Plus

Бренд: Jamara Страницы: 28

Бренд: K'Nex Страницы: 32

Бренд: K'Nex Страницы: 24

He 111H-6 nose interior

Бренд: Eduard Страницы: 6

KICK`N CRAWL BARN 71699

Бренд: Fisher-Price Страницы: 4

INTERNATIONAL LIGHTHING

Бренд: Sail Classics Страницы: 2

Бренд: Mega Bloks Страницы: 32

Бренд: Ripmax Страницы: 20

Бренд: Carson Страницы: 26

Бренд: KBT Страницы: 12

Бренд: K'Nex Страницы: 24

Premier Swiss 6/8 Type II Crocodile Electric Engine

Бренд: M.T.H. Страницы: 107

Lava Launch Coaster 50050

Бренд: K'Nex Страницы: 72

Бренд: MTHTrains Страницы: 49

Goblin 630 COMPETITION

Бренд: SAB Heli Division Страницы: 48

Бренд: Lionel Страницы: 8

Бренд: Horizon Hobby Страницы: 18

Boulton Paul Defiant Mk I

Бренд: WarbirdKits Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды