manualshive.com logo in svg

GREAT PLANES Ultra Sport 40 Plus, Инструкция по эксплуатации

Поделиться
Скачать
GREAT PLANES Ultra Sport 40 Plus Скачать руководство пользователя страница 56

power than a .46, yet fits in the same space as a .40. It’s a
clear gain in performance AND options, for sport flying and
aerobatics, and here's why. The 1-piece remote needle
valve can be repositioned for standard upright or side
mounting and the fuel inlet rotates, for ease either way you
go. Also included: dual bearings, an #873 muffler and 2-year
warranty. OSMG0550

O.S. FS-70 Surpass

™

II

Improve your fuel economy and increase your power with
the FS-70 Surpass II. It puts out an impressive 1.1
horsepower at 11,000 rpm – with all the power you need to
execute big maneuvers. Its Type 60R carb provides more
precise fuel flow control and smoother throttle control than
the original FS-70 Surpass. The FS-70 Surpass II also
features easier installation, adjustment and maintenance.
Muffler and glow plug included. Two-year warranty.
OSMG0872

Futaba

®

S3001 Standard Ball Bearing Servo

Futaba’s S3001 is a standard servo with nylon gears, “J”
connector and ball bearing on the output shaft. Length: 1.59
in. Width: 0.78 in. Height: 1.42 in. Weight: 1.6 oz. Torque:
33.3 oz-in (4.8V); 41.7 oz-in (6V). Transit time: 0.28 sec./60°
(4.8V); 0.22 sec./60° (6V). One year warranty. FUTM0029

Futaba S9001 Aircraft Coreless Ball Bearing Servo
Ideal for airplanes, sailplanes, helis, even nitro or electric
boats, the S9001 features a coreless motor for smooth, fast
response and a final gear with dual ball bearings for fast
transit time. It comes with “J” connector, one attached servo
horn, three extra horns and mounting hardware. Length:
1.59 in. Width: 0.78 in. Height: 1.42 in. Weight: 1.69 oz.
Torque: 54.1 oz-in (4.8V); 72.2 oz-in (6V). Transit time: 0.22
sec./60° (4.8V); 0.18 sec./60° (6V). One year warranty.
FUTM0075

Great Planes .40-Size Mechanical Retracts
Simple, sensibly priced, low-profile Great Planes retracts
offer a proven design and unique features. Mounting flanges
on the nylon-reinforced composite housing conform to airfoil
shapes, ensuring a neat, smooth appearance. A deployment
angle of 88° ensures virtually perfect support for wings with
0-2" dihedral. Include adjustable axles for no-bend
installation ease. Require wheel and retract servo.
Weight/retract: 5 oz. GPMQ2905

56

Содержание Ultra Sport 40 Plus































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды