GREAT PLANES Ultra Sport 40 Plus Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 62

GREAT PLANES Ultra Sport 40 Plus Скачать руководство пользователя страница 22

❏ ❏

49. Retractable Mains/Fixed Tailwheel. Fit your retractable

landing gear to the opening. Cut the sheeting as needed so
that the gear is flush with the sheeting. Once you are
satisfied with the fit, mark the holes for the landing gear onto
the mounting blocks.

❏ ❏

50. Retractable Mains/Fixed Tailwheel. Mix some epoxy

thinned with alcohol and brush it on the inside of the landing
gear compartment and on the edges of the sheeting to
reinforce it.

❏ ❏

51. Retractable Mains/Fixed Tailwheel. Drill a 1/4" [6.4mm]

hole through W1 and W2 as shown at the die-cut mark.

❏ ❏

52. Fixed Mains and Tailwheel. Locate the Fixed Mains

and Tailwheel landing gear cut-out template. Place it as
shown on the bottom sheeting. Cut the sheeting as indicated
by the template.

❏ ❏

53. Fixed Tricycle. Locate the Fixed Tricycle landing

gear cut-out. Place it on the landing gear rail as shown
above. Cut the sheeting as indicated by the template.

❏

54. If you have not done so, go back to step 4 and build

the left wing panel.

22

«
...
20
21
22
23
24
...
»

Содержание Ultra Sport 40 Plus































































Отзывы:

Нет отзывов