manualshive.com logo in svg

GREAT PLANES Giles G-202, Инструкция по эксплуатации

Поделиться
Скачать
GREAT PLANES Giles G-202 Скачать руководство пользователя страница 6

❏ ❏ 

1. Locate the servo cut out on the bottom of each wing

and cut the covering 1/8" [3mm] inside the edges of the
opening in the bottom of the 

right wing panel

for the aileron

servo. Use your Top Flite MonoKote

®

Trim Seal Tool

™

to seal

the covering to the sides of the opening.

Note:

You’ll notice a piece of string that passes through the

ribs at the location of the aileron servo well. Don’t remove
the string because you will use it to pull your aileron servo
cord through the wing later. Tape the string in place as shown.

❏ ❏ 

2. Locate the hole and cut the covering on the top of

the right wing panel for the string to exit. Remove the tape
from the wing root, and route it through the opening. Tape
the string to the top of the wing.

❏ ❏ 

3. Test fit the wing halves with the 

wing joiner.

The

tapered edge of the joiner faces the leading edge of the
wing. If necessary, sand any high spots on the root end of
the wing panels so there is 

no gap

when you join them.

❏

4. Tape a piece of wax paper or Great Planes Plan

Protector

™

over your work surface. Thoroughly coat the

joiner pockets

and the mating ends of 

both

wing halves with

30-minute epoxy. Set the wing halves aside and proceed
quickly. Coat all surfaces of 

one half

of the wing joiner with

30-minute epoxy and place it in one of the wing halves. Coat
the other half of the joiner with 30-minute epoxy and join the
other wing. Use a piece of balsa or cardboard to wipe away
excess epoxy. Use masking tape to tape the wing tightly
together. Use a paper towel dampened with alcohol to wipe
away any more epoxy that oozes out of the wing, then set
the wing aside. Do not disturb the wing until the epoxy has
fully cured.

❏

5. Locate the two 5/16" x 3-3/8" [8mm x 86mm]

hardwood wing dowels.

Slightly bevel the ends of the

dowels. Test fit the dowels into the wing, making sure they
lock into the holes inside the wing. If necessary, drill the
holes in the wing using a 5/16" [8mm] drill bit. Use 30-minute
epoxy to glue the dowels into the wing, allowing them to
protrude 1-1/8" [28mm].

Rudder Assembly

WING ASSEMBLY

6

Содержание Giles G-202





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды