GREAT PLAINS 5109 Скачать руководство пользователя страница 17

Страница: 17 / 38

TC5109-5323

Table of Contents

Index

Preparation and Setup

07/11/2018

Table of Contents

Index

566-224M

Hitching Turbo-Chisel to Tractor

Hitch to a tractor for highway transport or field

operations. Hitch to a leading implement only for field

operations. Do not transport behind another implement.
Before hitching, check the compatibility and capability of

the towing tractor or implement:
The TC5109-5323 Turbo-Chisel is a pull-type implement

equipped with a standard Category IV single tang hitch.

It may be converted to a Category III or clevis hitch using

supplied accessory parts.
To prevent soil compaction on rows, set tractor wheels

between rows. For hillsides and steep slopes, set tractor

wheels as wide as possible for maximum stability.
1. Raise tractor three-point arms (if equipped) clear up

to clear Turbo-Chisel.

2. For TWO-WHEEL DRIVE and MFWD tractors, pin

drawbar in fixed center position for field and

transport. For FOUR-WHEEL DRIVE and TRAC-

DRIVE tractors, leave one hole clearance on each

side of drawbar for field position, hitch damage may

occur if pinned solid. Pin in center position for

transport to maintain maximum steering control.

Refer to Figure 3

3. Use jack to raise and lower turbo-chisel tongue.
4. Back tractor draw bar into alignment with hitch .
5. Secure with a locking hitch pin.

Negative Tongue Weight Hazard:

Make certain that turbo-chisel is securely hitched to the

tractor or leading implement before unfolding. An unhitched
turbo-chisel can tip over backwards during folding and

unfolding if the tongue is not secured.

6. Secure safety chain to an anchor on the tractor.

Refer to Figure 4

7. Retract jack foot. Re-orient jack to storage position.
8. After hitching tractor to turbo-chisel, store jack on

storage stob on Turbo-Chisel tongue.

Load Sway Hazard:

Lock drawbar swing to center position to minimize any
side-to-side sway to assure proper tracking in the field,

and safe road travel. See

“

Transport

” on page 19, for

safe transporting.

Figure 3

Jack & Hitch Clevis

41993

Crushing Hazard:

Do not stand or place any body part between turbo-chisel and
moving tractor. You may be severely injured or killed by being

crushed between the tractor and turbo-chisel. Stop tractor

engine and set parking brake before attaching cables and
hoses.

Figure 4

Jack in Storage

41994

Содержание 5109







































Результаты поиска

Содержание 5109

Отзывы:

Похожие инструкции для 5109

Бренды по названию

Популярные бренды

GREAT PLAINS 5109, Руководство оператора

Результаты поиска

Содержание 5109

Отзывы:

Похожие инструкции для 5109

Бренды по названию

Популярные бренды