55
EFFECTS
CAUSES
SOLUTIONS
Cloudy water
Green coloured
• Dirty filter
• pH incorrect
• Formation of algae
• Washing the filter.
• Re-adjustment
• Shock treatment
The pump does not start
• Breaker disconnected
• Fuse burnt
• Turbine blocked
• Re-start
• Replace it
• Check that the fan at the rear of the
motor turns
The pump turns but does not discharge • Suction flaps closed
• The skimmer sucks air
• Pre-filter full
• Air inlet in the cover
• Defective turbine
• Open them again
• Rectify water level
• Clean it
• Check the seal and change the pre-
filter cover
• Change the turbine
The skimmer does not suck
• Basket full
• Flap not closed well
• Water level too low
• Empty it
• Open it
• Re-adjust it
Dirty water returned to pool
• Filter obstructed
• Wash it, rinse it
Pressure in pressure gauge too high
• Filter washing badly done
• Outlet flap closed
• Repeat it
• Open the trap, check condition of sand
(change it every 3 or 4 years)
The pool cleaner does not suck or does
not suck enough
• Pre filter obstructed
• Corresponding flap closed
• Tube worn or perforated
• Air in the tubes
• Other flaps open
• Dirty filter
• Clean it
• Open it
• Replace it
• Purge and wait for priming
• Close them
• Clean it
Corrosion marks
• pH very low
• Increase pH to 7.2 - 7.4
Sand in the pool
• Mesh broken
• Manipulation of the multi-directional
flap with the pump working
• Filter inversely connected The tubes
have been inverted during assembly.
• Change the mesh
• Change the multi-directional flap
• Correctly connect the filter
- Chlorine treatments: Consist in increasing the chlorine level until approximatively 20 ppm to eliminate germs and seaweeds. This
process has to be done only when the pool water comes from rivers or ponds, … or if it stayed a long time without any treatments.
- Checking: Check at least once a week the chlorine levels (use a chlorine and pH analyser). In the same way, we advise to add
an algicid to prevent seaweeds appearance.
Never have a swim before the chlorine level stabilization. Do always use a floating dispenser for the chemical product (tablets)
dissolution. The chemical product measuring out has to be done in accordance with: Your pool water volume, the bathe frequency,
the climatic conditions, the water temperature and the location. Do always move the water and wait for the chemical product
dissolution before adding another one. Wait approximatively 12 hours between any pH, chlorine or algicid adjustment using the
filter system.
MECHANICAL MEASURES:
Check the filter, the skimmer, the valves and the pipes are well connected to the pool. Do consider high water temperature will
involved more time for the filtering. Theoretic filtering time = Water volume / Filter system discharge (generally 8h/day with water
temperature of 21°C), (Ideal: 2h in the morning – 4h around midday – 2h in the afternoon). PLEASE RESPECT THE CONTINUOUS
WORKING PERIOD INDICATED IN THE FILTER MANUALS.
VACUUM CLEANER (MANUAL OR AUTOMATIC):
Only for pools with skimmer. Connect an hose extremity to the brush head and immerse it into the water to make it fill in. Connect
the other pipe extremity to the exhaustion adapter (TA) and place it above the skimmer basket. Switch on the filter in the FILTER
position and begin to clean the bottom. Pay special attention to areas with folds where dirt accumulates.
BOTTOM CLEANER VENTURY STYLE:
Connect a garden hose to the bottom cleaner join and introduce it into the pool. Open the tap until a normal pressure to make the
water flow out against the bottom of the pool, producing in that way an ascendant stream which leave the dirt into the filter (bag)
which is adjust on the bottom cleaner.
Содержание KWOV436
Страница 2: ......