background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors  Id. No. 0061845    04/2010    

22 

initial date of purchase. We will not consider any claims which do not fall within this 
description.  Costs  of  transport,  packaging,  freight  and  journeys  are  payable  by  the 
purchaser.  We  accept  no  liability  for  transport  damage.  Please  send  the  offending 
item to GRAUPNER or to the approved service centre for your country, and include a 
concise,  accurate  description  of  the  fault  together  with  the  dated  purchase  invoice. 
The  guarantee  does  not  cover  failure  of  any  part  of  the  model  due  to  an  accident, 
incompetent handling, or incorrect use. 
 

Important: before you start construction 

Even  if  you  have  already  built  a  large  number  of  RC  models  please  read  right 
through these instructions and check that all the kit components are actually present. 
We  have  taken  great  trouble  to  keep  construction  as  simple  as  possible,  without 
making any compromises in the area of safety.

 

 
This model  is  highly  pre-fabricated  and  can be  built  in  a  very  short  time.  However, 
the work which you have to carry out is important and must be done carefully. The 
model  will  only  be  strong  and  fly  well  if  you  complete  your  tasks  competently  -  so 
please work slowly and accurately. 
 

When  self-tapping  screws  have  to  be  screwed  into  wood,  apply  a  little  white 
glue to prevent them working loose: just squirt white glue into the hole and fit 
the screw. 
 
 
Operating the CLUB STAR II 
Be  sure  to  read  right  through  the  operating  and  assembly  instructions  before 
you attempt to fly the model for the first time. You alone are responsible for the 
safe  operation  of  your  radio-controlled  model.  Young  persons  under  fourteen 
years should only be permitted to operate this model under the instruction and 
supervision of an adult who is aware of the hazards involved in this activity. 
Please keep these operating instructions in a safe place. If you ever dispose of 
the  model,  be  sure  to  pass  them  on  to  the  new  owner.  If  you  have  any  ques-
tions regarding the safe operation of your RC model aeroplane, please turn to 
your local model shop in the first instance, as the staff will be pleased to help 
you. 
 
Powered  model  aircraft  are  very  demanding  and  potentially  dangerous  ma-
chines, and call for a high level of technical knowledge and skill from the op-
erator, together with a responsible attitude. 
 
In  legal  terms  our  models  are  classed  as  aircraft,  and  as  such  are  subject  to 
legal  regulations  and  restrictions  which  must  be  observed.  Our  brochure 
“Modellflugrecht,  Paragrafen  und  mehr”  (Model  Aviation  Law,  Legal  Require-
ments  and  more)  is  available  under  Order  No.  8034.02,  and  contains  a  sum-
mary of all these rules. Your local model shop should have a copy which you 
can  read.  Models  fitted  with  glowplug  engines  may  only  be  flown  with  the 
landowner’s  permission,  and  third  party  insurance  is  mandatory.  There  are 
also Post Office regulations concerning your radio control system, and these 
must be observed at all times. 
 

Содержание CLUB STAR II



























Отзывы: