GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten!
0058434
11/2007
17
If you intend to operate the boat with a steam engine installed, it is important to run-in the power plant on
the bench before installing it in the model. This is particularly important for adjusting the flame height
accurately: open the gas regulating valve just to the point where the flame burns cleanly, without any
yellow coloration, and without soot formation. One gas fill provides around 25 minutes of running, although
for safety’s sake you should either refill the gas tank earlier than this, or keep the boat close to the bank
after about 15 - 20 minutes’ running. When the flame goes out, the steam engine stops immediately, and
this could present you with problems in salvaging the boat. Open the regulating valve slightly when re-
filling the tank, as the liquid gas will force the air in the tank out due to its lighter weight. The tank is full
when liquid gas squirts out of the nozzle. Don’t forget to check the water level in the boiler.
Using an exhaust steam condenser helps considerably to prevent the model becoming soiled with a
mixture of condensed water and oil. Remember to empty it after every second or third run.
For more details concerning the operation of the steam engine please refer to the operating instructions
supplied with the power plant.
Parts List -
ALTONA
Part
No.
Description
No.
off
Material
Dimensions in mm
1
Hull
1
GRP
Ready made
2
Front boatstand support
1
Plywood
Laser-cut 6 mm
3
Rear boatstand support
1
Plywood
Laser-cut 6 mm
4
Boatstand connecting piece
2
Plywood
Laser-cut 6 mm
5
Boatstand lining strip
1
Adhesive tape
Order No. 741
6
Stern
1
GRP
Ready made
7
Rudder blade and shaft
1
GRP
Ready made
8
Rudder bush
1
Brass
6 / 5 Ø x 33 mm
9
Pivot sleeve
2
Brass
5 / 4 Ø x 5 mm, overlength
10
Tiller
1
Plastic
Ready made, Order No. 2400
11
Stern tube and shaft
1
Brass and V2A
Ready made, Order No. 327.215
12
Stern bulkhead
1
Plywood
Laser-cut
13
RC installation plate
1
Plywood
Laser-cut
14
Base plate
1
Plywood
Laser-cut, 6 mm
15
Mounting block
2
Beech
25 x 25 x 17 mm
16
Main deck
1
GRP
Ready made
17
Hawse pipe
2
Aluminium tube
10 / 9 Ø x 75 mm, overlength
18
Chain pipe
2
Aluminium tube
7 / 6.2 Ø x 25 mm, overlength
19
Bulwark stanchion
46
ABS
Laser-cut
20
Reinforcement
46
ABS
Laser-cut
21
Cable hawse, two-part
8
ABS
Vac.-moulded
22
Bollard
12
Aluminium tube
10 / 9 Ø x 50 mm, overlength
23
Transverse bar
13
Aluminium rod
3 Ø x 25 mm, overlength
24
Bollard cap
13
ABS
Laser-cut
25
Support plate
6
ABS
Laser-cut
26
Bow section
1
ABS
Laser-cut
27
Bow bollard
1
Aluminium tube
10 / 9 Ø x 85 mm, overlength
28
Transverse bar
1
Aluminium rod
3 Ø x 25 mm
29
Stern platform
1
Mahogany
5 x 2 x 1000 mm overall
30
Stanchion
5
Mahogany
6 x 6 x 18 mm
31
Awning
1
Fabric
450 x 300 mm
32
Awning retaining cable
1
Thread
0.8 Ø x 2000 mm
33
Awning framework
1
Brass rod
2 Ø x 4000 mm overall
34
Washer
8
Plated brass
2.2 Ø x 4.5 mm
35
Lamp platform
1
ABS
Laser-cut
36*
Stern light
1
Plastic
Ready made
37*
Flagstock
1
Plastic
Ready made, Order No. 316.2
38*
Flagstock base
1
Plastic
Ready made
39*
Anchor winch
1
Plastic
Ready made
40*
Anchor
2
Metal
Ready made
41*
Anchor chain
2
Metal
250 mm
42
Tyre fender, two-part
10
ABS
Vac.-moulded
