background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors 

                    12/2010 

0062196 

23 
 

the best route to it. Look around for landmarks in the countryside which will help you locate 
the model when searching. 
 
However, the main point to remember when scratching for a thermal below launch height is - 
“don't panic”: remember that in almost every case it is the pilot that is the problem, rather 
than the model. If you have a flying colleague who tries to help by giving a continuous 
commentary and giving what he thinks is useful advice all the time, tell him to shut up. A 
colleague who wishes to help you will restrict himself to very short and really helpful com-
ments, e.g. by pointing out other models whose pilots have found a thermal, a circling bird of 
prey or a safe approach to the planned landing site. A really good friend will even launch his 
own model, fly down into the valley and help you find a thermal. With two models the 
chances of success are much higher. 
 

Safety 

Safety is the First Commandment when flying any model aircraft. Third party insurance 
should be considered a basic essential. If you join a model club suitable cover will usually be 
available through the organisation. It is your personal responsibility to ensure that your 
insurance is adequate. Make it your job to keep your models and your radio control system in 
perfect order at all times. Check the correct charging procedure for the NC batteries used in 
your RC set. Make use of all sensible safety systems and precautions which are advised for 
your system. Gather as much information as you can from various product catalogues, and 
from your local model shop proprietor. 
Always fly with a responsible attitude. You may think that flying low over other people’s 
heads is proof of your piloting skill, but others know better: the real expert does not need to 
prove himself in such childish ways. Let other pilots know that this is what you think too. 
Always fly in such a way that you avoid endangering yourself or others. Bear in mind that 
even the best RC system in the world is subject to outside interference. No matter how many 
years of accident-free flying you have under your belt, you have no idea what will happen in 
the next minute. 
 

The fascination of it all 

 
Model flying is, and always has been, a fascinating hobby. Take your time to get to know 
your new 

Alpina 3001 ELEKTRO

 really well. Plan to spend many hours in the open air, 

where you will learn to appreciate the model’s outstanding performance, its docile handling 
and its wide-ranging potential. 
You can join us in savouring one of the few types of sport which combine high technology, 
manual dexterity, and sophisticated personal skills. You can fly alone or with friends, and at 
the same time you can enjoy the pleasures of nature - treats which have become rare in 
today's world. 
 
We - the GRAUPNER / TANGENT Modellsport team - wish you many hours of pleasure in 
building and flying your new model. Happy landings! 
 
 
GRAUPNER / TANGENT Modellsport 

 
 
Dieter Bär – Model Development 
 

Содержание ALPINA 3001 ELEKTRO





























Отзывы: