background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors 

                    12/2010 

0062196 


 

Duration of validity 
 
This declaration only applies to claims made to us during the claim period as stated 
in this declaration. The claim period is 24 months from the date of purchase of the 
product by the consumer from a dealer in the Federal Republic of Germany (date of 
purchase). If a defect arises after the end of the claim period, or if the evidence or 
documents required according to this declaration in order to make the claim valid are 
not presented until after this period, then the consumer forfeits any rights or claims 
from this declaration. 
 
Limitation by lapse of time 
 
If we do not acknowledge the validity of a claim based on this declaration within the 
claim period, all claims based on this declaration are barred by the statute of 
limitations after six months from the time of implementation; however, this cannot 
occur before the end of the claim period. 
 
Applicable law 
 
This declaration, and the claims, rights and obligations arising from it, are based 
exclusively on the pertinent German Law, without the norms of international private 
law, and excluding UN retail law. 
 

The following points are important and must be observed at all times: 



Before you fly the model check that the radio control system is working reliably, 
and that all connections are secure. 



The batteries must be charged and the range of the radio control system must be 
checked before you operate the model. In particular, the radio control system 
batteries must be fully charged before each session. 



Ensure that the channel you intend to use is not already in use by other 
modellers. Never fly the aeroplane if you are not certain that your channel is free. 



Read and observe the instructions and recommendations provided by the 
manufacturer of your radio control system and accessory components. 



Ensure that the servos are not mechanically obstructed at any point in their 
travel. 



Dry cells and rechargeable batteries must never be short-circuited. 



Remove all batteries from the model prior to transporting and storing it. 



Do not subject the aircraft to dirty or cold conditions, or high levels of humidity or 
heat. 



Secure the model and your RC equipment carefully when transporting them. 
They may be seriously damaged if they are free to slide about. 



IMPORTANT:

 when the flight battery is exhausted, you must not dispose of it in 

the household waste. Take the pack to your local battery reclamation centre. 

 IMPORTANT:

 when the useful life of the model and the transmitter are over, do 

not discard them in the domestic rubbish. The electric and electronic components 

Содержание ALPINA 3001 ELEKTRO





























Отзывы: