background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors 

                    12/2010 

0062196 


 

Flying the model 

Never fly your 

ALPINA 3001 Champ ELEKTRO 

in a nature reserve or any other 

protected site. Please don’t disturb the animals and plants which live in the 
countryside. 
Trees and bushes are the natural habitat of many birds, and also serve as nesting 
sites and general protection for them. 

 
 

Before you fly the model for the first time it is essential to take out a special 
insurance policy designed to cover modelling risks. 
These safety notes should be kept in a safe place. If you ever dispose of the 
model, be sure to pass them on to the new owner. 

 
Manufacturer’s declaration: 
If material defects or manufacturing faults should arise in a product distributed by us 
in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, 
Graupner GmbH & Co. KG, D-73230 Kirchheim/Teck, Germany, acknowledge the 
obligation to correct those defects within the limitations described below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in 
the usability of the product is due to natural wear, use under competition conditions, 
incompetent or improper use (including incorrect installation) or external influences. 
This manufacturer’s declaration does not affect the consumer’s legal or contractual 
rights regarding defects arising from the purchase contract between the consumer 
and the vendor (dealer). 
 
Extent of the guarantee 
 
If a claim is made under guarantee, we undertake at our discretion to repair or 
replace the defective goods. We will not consider supplementary claims, especially 
for reimbursement of costs relating to the defect (e.g. installation / removal costs) and 
compensation for consequent damages unless they are allowed by statute. This does 
not affect claims based on legal regulations, especially according to product liability 
law. 
 
Guarantee requirements 
 
The purchaser is required to make the guarantee claim in writing, and must enclose 
original proof of purchase (e.g. invoice, receipt, delivery note) and this guarantee 
card. He must send the defective goods to us at his own cost, using the address 
stated above. 
The purchaser should state the material defect or manufacturing fault, or the 
symptoms of the fault, in as accurate a manner as possible, so that we can check if 
our guarantee obligation is applicable. 
The goods are transported from the consumer to us and from us to the consumer at 
the risk of the consumer. 
 
 

Содержание ALPINA 3001 ELEKTRO





























Отзывы: