GRASS VALLEY LDX 864K Скачать руководство пользователя страница 81

Страница: 81 / 122

LDX 86 High Frame Rate/HD/3G/4K Camera Platform User’s Guide (v2.0)

Chapter 5 - Camera menu reference

Super Coarse

On, Off

Off

User 0

Oper

Switches super coarse detail enhancement on
or off.

Detail Level

0..99

User 0

Oper

Sets detail level for viewfinder signal.

Slicer

0..99

User 0

Oper

Sets the noise slicer level for VF detail.

Vert Detail Lvl

0..99

User 3

Oper

Sets the level of the vertical component in
the detail signal

Coarse/Fine

0..99

User 3

Oper

Sets detail balance between coarse and fine
structures (0 = coarse, 99 = fine).

Level Dep

0..99

User 3

Oper

Sets the level where the detail enhancement
starts to work.

Soft Detail

On, Off

User 3

Oper

Switches Soft Detail on or off. Reduces the
amount of detail added for large transitions.

Soft Detail Lvl

0..99

User 3

Oper

Sets the upper limit level of detail
enhancement for soft detail.

VF Mode

Combined, 1
Phase, 2 Phases, 3
Phases

Combin

User 2

Oper

Sets way of combining phases in high speed
cameras and video modes to output to the
viewfinder.

Menu Settings

Rotary Speed

1..10

User 2

Oper

Selects the sensitivity of the menu navigation
rotary control.

Menu Display

On, Time

Time

User 2

Oper

Selects the camera menu to be permanently
On or to disappear after a set Time.

Menu Time

3..30

User 2

Oper

Sets the time (in seconds) the menu is
displayed when Menu Display is set to Time.

Menu White Lvl

0..99

User 2

Oper

Sets the white level (brightness) of the
characters of the menu.

Intercom

Prod Vol Ctrl

Prod, Master

Prod

User 3

Oper

Selects if the Prod volume control (upper
rotary at the back panel) controls Prod channel
volume only (Prod) or overall (Master) intercom
volume.

Cam Sidetone

0..99

User 3

Oper

Sets the sidetone level (audio feedback from
mic to headset) in the camera operator’s
headset.

Tracker Sidetone

0..99

User 3

Oper

Sets the sidetone level (audio feedback from
mic to headset) in the tracker’s headset.

Buttons

SW1

Call, EXT1, EXT2,
PROD, ENG, Select

EXT1

User 0

Oper

Assigns a function to user button SW1.

SW1 Mode

Mom, Alt

Mom

User 0

Oper

Selects switching mode for SW2: momentary
(push) or alternating (toggle).

SW2

EIris, Zoom,
FocAst, EXT1,
EXT2, PROD, ENG

Ext2

User 0

Oper

Assigns a function to user button SW2.

SW2 Mode

Mom, Alt

Mom

User 0

Oper

Selects switching mode for SW2: momentary
(push) or alternating (toggle).

PickMe Mode

Mom, Alt

Mom

User 1

Oper

Selects switching mode for the PickMe
buttons: momentary (push) or alternating
(toggle).

Menu item

Values

Default

Level

File

Description

Содержание LDX 864K



























































































































Результаты поиска

Содержание LDX 864K

Отзывы:

Похожие инструкции для LDX 864K

Бренды по названию

Популярные бренды

GRASS VALLEY LDX 864K, Руководство пользователя

Результаты поиска

Содержание LDX 864K

Отзывы:

Похожие инструкции для LDX 864K

Бренды по названию

Популярные бренды