GRASS VALLEY LDX 864K Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 122

background image

52

LDX 86 High Frame Rate/HD/3G/4K Camera Platform User’s Guide (v2.0)

Chapter 3 - Operating instructions

3.10.2 Adjusting intercom volume

Use the rotary controls at the back panel of the camera to adjust the audio volume of the three
intercom channels:

•

Prod

—adjusts the volume of the production channel intercom signal.

•

Prog

—adjusts the volume of the program intercom channel signal.

•

Eng

—adjusts the volume of the engineering intercom channel signal.

To adjust the audio volume of the signal from the Tracker headset microphone go to the

CONFIGURATION

>

INTERCOM

menu and change the

CAM

TRACKER

LVL

item.

3.10.3 Routing signals

By default, all three intercom channels are audible on both muffs (left and right) of the camera
headset. The routing of the intercom channels can be changed to personal preference. Go to
the

CONFIGURATION

>

INTERCOM

menu to set up the routing:

•

Cam Prod

—selects to which ear muff(s) of the camera headset the production intercom

channel is routed.

•

Cam Eng

—selects to which ear muff(s) of the camera headset the engineering intercom

channel is routed.

•

Cam Prog

—selects to which ear muff(s) of the camera headset the program intercom

channel is routed.

•

Cam Tracker

—selects to which ear muff(s) of the camera headset the Tracker’s

microphone signal is routed (when a Tracker headset is connected).

Intercom microphone gain, 12V bias tee power supply and microphone on/off switches are also
available in this menu.

3.10.4 Adjusting sidetone volume

Sidetone levels (this is audio feedback from microphone to ear muffs) for camera and Tracker
headsets can be adjusted in the

OPERATOR

TOOLBOX

>

INTERCOM

menu:

•

Cam Sidetone

—adjusts the sidetone level of the camera operator’s headset from 0

(muted) to 99 (loudest).

•

Tracker Sidetone

—adjusts the sidetone level of the Tracker’s headset from 0 (muted) to

99 (loudest).

☞

Note

☞

Note

Only the sidetone levels for the right side ear muff can be adjusted. The left ear muff always
has a fixed sidetone level.

3.10.5 Assigning buttons

The user buttons at the left side panel of the camera (SW1 and SW2), the user button under
the handgrip and the VTR button on the lens can also be used to send the intercom signal from
the headset to Production or Engineering.

«
...
50
51
52
53
54
...
»

Содержание LDX 864K



























































































































Отзывы:

Нет отзывов

Похожие инструкции для LDX 864K

Бренд: Vivitar Страницы: 37

Бренд: RHINO Страницы: 23

Бренд: Talitor Страницы: 8

Бренд: Panasonic Страницы: 71

Бренд: Panasonic Страницы: 58

Бренд: UDP Technology Страницы: 23

Бренд: Sony Страницы: 4

Бренд: Steren Страницы: 2

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 154

Бренд: JVC Страницы: 2

Бренд: JVC Страницы: 52

Бренд: JVC Страницы: 56

Бренд: JVC Страницы: 56

VPC-GH2 - Full HD 1080 Video

Бренд: Sanyo Страницы: 79

VPC-GH4 - Full HD 1080 Video

Бренд: Sanyo Страницы: 204

Бренд: Sanyo Страницы: 243

Бренд: Sanyo Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды