GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 26

Страница: 26 / 86

HD Wireless User’s Guide (v6.2)

Chapter 2 - Installation

2.4 Wireless Control Unit (WCU)

An optional mounting kit is available for mounting the WCU into a standard 19-inch rack.

Caution

When installing the WCU always allow 1 RU space above and below the WCU to properly
ventilate the unit.

Connection steps:

Connect the triax cable from the AMU to the Triax input 1

of the WCU. If you use a

second AMU, connect it to Triax input 2

of the WCU.

Connect the OCP to the C2IP network

Connect a digital monitor (SD or HD) to the SDI3 (OSD) output

Connect the SDI1 and SDI2 outputs

of the WCU to the studio system.

If required, provide a reference signal to the Genlock input

of the WCU (SD black-burst,

CBVS and HD-TLS are supported). Terminate the looped-through connector with 75



Connect an analog (SD) monitor to CVBS output connector 1 (OSD) or 2

Connect the intercom

system (see below).

Connect the signalling

system (see below).

Connect the audio

10.

Connect the WCU power socket

to the mains power supply.

Figure 2-7.

WCU connections

TRIAX

GENLOCK

C.V.B.S.

(OSD)

SERIAL DIGITAL OUTPUT

Data1

Sign

I / Com

RS232

Audio out

Network

Содержание HD WIRELESS -























































































Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды