manualshive.com logo in svg

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Поделиться
Скачать
GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 13

HD Wireless User’s Guide (v6.2)

13

Zusammenstellung von in diesem Handbuch verwendeten Warnhinweisen:

•

Immer von der Netzversorgung trennen, bevor der Adapter geöffnet wird.

•

Stecker zwischen Kamerakopf und Adapter mit äußerster Vorsicht handhaben. Darauf 
achten, dass die Steckerstifte nicht durch die Führungsstifte beschädigt werden.

•

Diese Schritte in der angegebenen Reihenfolge ausführen.

•

Das Anziehen der Schrauben in der falschen Reihenfolge kann zu mechanischen Schäden 
an der Kamera führen.

•

Das Lösen der Schrauben in der falschen Reihenfolge kann zu mechanischen Schäden an 
der Kamera führen.

•

Niemals einem Adapter Strom zuführen, ohne sich zuerst zu vergewissern, dass die 
Antennen angebracht sind.

•

Es dürfen nur die mitgelieferten Antennen verwendet werden.

•

Vor dem Abnehmen der Antennen muss die Stromzufuhr zu den Geräten abgeschaltet 
werden.

•

Die Eingangsspannung darf nie +17 VDC überschreiten.

•

Vor dem Öffnen des AMU muss die Stromzufuhr zum WCU abgeschaltet werden.

Содержание HD WIRELESS -























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды