GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 22

Страница: 22 / 86

HD Wireless User’s Guide (v6.2)

Chapter 2 - Installation

2.2.2 Attaching antennas to the adapter

The wireless camera adapter uses two different antennas: a Data link antenna and a Video link
antenna. Attach both antennas securely to the wireless adapter.

Figure 2-3.

Attaching the antennas

The following tables show which antenna to use for the chosen frequency ranges.

Caution

Never supply power to an adapter without first ensuring that the antennas are attached.



Always use the antenna that was supplied with the frequency module. Using the wrong
antenna will result in poor coverage.



Always switch off the power to the units before detaching the antennas.

Video frequency

Identification ring

2.0 to 2.2 GHz

Black ring + code ‘0’

2.2 to 2.4 GHz

Red ring + code ‘2’

2.5 to 2.7 GHz

Green ring + code ‘5’

Data frequency

Antenna type

456 MHz

3922 407 56351 (length: 160 mm / 6.3”)

Data RF antenna

Video RF antenna

Identification ring

Содержание HD WIRELESS -























































































Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды