manualshive.com logo in svg

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Поделиться
Скачать
GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 8

8

HD Wireless User’s Guide (v6.2)

Warnings

•

Do not modify this equipment. 

•

Do not use this equipment in areas where it may endanger safety such as hospitals or 
airports.

•

This equipment generates electromagnetic radio frequencies. Installation must conform 
to the instructions given in this manual.

•

Installation of this equipment must only be performed by qualified personnel. 

•

Do not use any accessories other than those recommended by the manufacturer.

•

The current and voltages present in this equipment are dangerous. Personnel must at all 
times follow the safety regulations.

•

Always disconnect power before removing covers or panels. 

•

Always discharge high voltage points before servicing. 

•

Never make internal adjustments, perform maintenance or service when alone or when 
fatigued.

•

In case of an emergency ensure that the power is disconnected.

•

Mount equipment so that power lead can be accessed to disconnect power.

•

The power lead of the WCU must always be connected to a power socket with a 
protective earth.

•

Any interruption of the protection conductor inside or outside the apparatus, or 
disconnection of the protective earth terminal, is likely to make the apparatus dangerous. 
Intentional interruption is prohibited. 

•

Use only the antennas supplied. Do not use the camera without antennas. Switch off 
power to the units before detaching antennas.

•

Avoid contact with the right side cover of the camera during operation as it may become 
hot.

Cautions

•

To prevent risk of overheating, ventilate the product correctly: when installing the LDK 
4470 Wireless Control Unit (WCU) always allow 1 RU space above and below the unit for 
ventilation.

•

Connect the product only to a power source with the specified voltage rating.

•

Always switch off the camera before changing the battery or changing the power supply.

•

Any cables connected to the camera must be less than 3 m (10 ft) to avoid interference.

Содержание HD WIRELESS -























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды