GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 84

Страница: 84 / 86

HD Wireless User’s Guide (v6.2)

Chapter 9 - Installing the Video booster

9.2 Assembly

Switch off the camera.

Remove the battery from the camera adapter.

Plug the booster onto the camera adapter battery plate.

Plug the XLR-4 power cable from the booster in the XLR-4 power receptacle on the
camera adapter.

Connect the RF coaxial cable between the output of the camera adapter and the input of
the booster.

Screw the correct flexible antenna on the booster according to your RF module:

–

use the LDK5457/20 antenna with LDK5466/20 RF module (2.0 to 2.2 GHz)

–

use the LDK5457/22 antenna with LDK5466/22 RF module (2.2 to 2.4 GHz)

–

use the LDK5457/25 antenna with LDK5466/25 RF module (2.5 to 2.7 GHz)

Install the battery onto the back panel of the booster.

Switch on the camera.

XLR-4 Power cable

RF coaxial cable

Flexible
antenna

Содержание HD WIRELESS -























































































Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды