GRASS VALLEY HD WIRELESS - Скачать руководство пользователя страница 48

Страница: 48 / 86

HD Wireless User’s Guide (v6.2)

Chapter 4 - Setting up

4.4.5 WCU audio menu

Select 1 or 2 audio channels, audio output level and delay

The number of audio channels can be selected in the menu of the WCU:

Menu path:

AUDIO_INTERCOM

AUDIO

MODE

Set the audio output level to enable (+6 dB) or to disable (0 dB):

Menu path:

AUDIO_INTERCOM

AUDIO

LEVEL

1(2)

The audio delay function delays the audio signal so that it is synchronised with the video
signal.

Menu path:

AUDIO_INTERCOM

AUDIO

DELAY

4.4.6 WCU intercom menu

Select a 2-wire or a 4-wire system

Depending on the intercom wiring set the wire mode for the Eng and Prod intercom
channels to 2wires or 4wires.

Menu path:

AUDIO_INTERCOM

INTERCOM

ENG

WIRE

MODE

Menu path:

AUDIO_INTERCOM

INTERCOM

PROD

WIRE

MODE

Select channel input level

For each intercom channel you can enable (+6 dBU) or disable (0 dBU) the level.

Menu path:

AUDIO_INTERCOM

INTERCOM

ENG

LEVEL

Menu path:

AUDIO_INTERCOM

INTERCOM

PROD

LEVEL

Menu path:

AUDIO_INTERCOM

INTERCOM

PROG

LEVEL

Select intercom output level

Adjust the output level as required.

Menu path:

AUDIO_INTERCOM

INTERCOM

ENG

(PROD)

OUT

REF

LEVEL

Adjust 2-wire balance

Set local side tone in the camera to zero.

Camera system menu path:

INSTALL

INTERCOM

SIDE

TONE

Adjust the output level to minimize the feedback from the headset microphone to the
headset muff.

WCU menu path:

AUDIO_INTERCOM

INTERCOM

ENG

(PROD)

BALANCE

Reset the local side tone in the camera to a comfortable value.

Содержание HD WIRELESS -























































































Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды

GRASS VALLEY HD WIRELESS -, Руководство пользователя

Результаты поиска

Содержание HD WIRELESS -

Отзывы:

Похожие инструкции для HD WIRELESS -

Бренды по названию

Популярные бренды