Grant Aerona3 Series Скачать руководство пользователя страница 61

Страница: 61 / 88

Section 14: Control Panel

Page 61

Table 14-4:

Control panel key

Key

Item

Description

Heat meter

Refer to Section 7.2 for further information

Electricity meter

Refer to Section 7.3 for further information

Overheat thermostat

The safety overheat thermostat will automatically switch off the boiler in the case of a control

malfunction causing overheating. If this occurs, the boiler will not light until the thermostat is reset.

To reset:

•

Unscrew the small plastic cap (refer to Figure 13-2)

•

Insert a small pointed implement into the hole and press the reset button

•

Replace the cap

If this condition continually repeats, contact your Service Engineer.

On / Off switch

This switch allows the hybrid unit to be switched off and back on as and when required. With this

switch set to OFF, neither the heat pump or the oil boiler will operate. This will override all heating

demands from the control system for the unit to start.
IMPORTANT: Setting this switch to OFF

DOES NOT

isolate the electrical supply to the heat pump

or the oil boiler. To fully isolate both heat pump and oil boiler unit, use the lockable external isolator

installed to provide power to the hybrid. Refer to Section 12 (electrical) for details of electrical

wiring.

Oil / Hybrid switch

This switch allows selection of either the 'hybrid' or 'oil' modes of operation, as follows:

•

Hybrid

- when the switch is set to this, the heat pump either operates alone or in conjunction

with the oil boiler, depending on air control thermostat setting.

•

Oil

- when the switch is set to this, only the oil boiler can operate.

Set the switch to this option if the oil boiler is to operate in a 'stand-alone' situation, i.e. if the

heat pump has not yet been installed, or it has been shut down for maintenance.

Fuse - heat meter (1 amp)

This fuse protects the electrical supply to the heat meter.

Fuse - heating controls (5 amps)

This fuse protects the electrical supply to the external heating system controls and the oil boiler.

Boiler control thermostat

This controls the boiler flow temperature level. It has two temperature settings (R1 and R2).

Refer to Section 15.6.1 (commissioning) for details on how to set the boiler control thermostat.

Air control thermostat

This monitors the ambient (outdoor) air temperature. It has two temperature settings (R1 and R2).

Refer to Section 15.6.2 (commissioning) for details on how to set the air control thermostat.

Figure 14-3:

Control panel

Содержание Aerona3 Series

























































































Результаты поиска

Содержание Aerona3 Series

Отзывы:

Похожие инструкции для Aerona3 Series

Бренды по названию

Популярные бренды

Grant Aerona3 Series, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Aerona3 Series

Отзывы:

Похожие инструкции для Aerona3 Series

Бренды по названию

Популярные бренды