grandimpianti WR 11, Инструкция по установке и эксплуатации

Страница: 12 / 69

9
in the event of a depression. This device has
a rear outlet which may liberate innocuous
steam during heating. Do not close or couple
it.
THE GUARANTEE DOES NOT COVER
DAMAGE CAUSED BY INCORRECT
INSTALLATION.
INSTRUCTIONS FOR THE USER
6. INFORMATION ON THE WASHING
MACHINE
6.1 DESCRIPTION OF THE MACHINE
It is composed of the following main parts:
1) Lid under which the control circuit is
lodged
2) Soap dispenser for pre-wash, wash (foam
damping washing powder) and rinse liquid
(foam damping)
3) Loading door
4) Cycle selection push button panel
5) Cycle status dial
6) Door pilot lamp (when on, the door can be
opened)
7) Main switch
8) Start and cycle forward push button
9) Rinse selector (2 or 4 rinses)
10) Coin meter *
11) Pilot light *
12) Cycle forward push button *
(* only on machines with coin-meter).
IMPORTANT: THE ENCLOSED DIA-
GRAMS ARE NECESSARY FOR IDEN-
TIFYING AND ORDERING SPARE
PARTS.
6.2 APPLICATION RANGE
Your washing machine was designed to wash
synthetic fabrics, woollens, cottons, linens.
Choose your cycle by the appropriate push
buttons as suggested by the labels attached
to the garments.
6.3 INFORMATION ABOUT THE
ELECTRICAL INSTALLATION
The built-in electrical installation is com-
posed of protection and control devices that
are lodged on a panel in the upper part of the
machine. The wiring diagrams and lists are
reported below.
6.4 DOCUMENTS THAT CERTIFY
MACHINE CONFORMITY
The washing machine described in this book-
let complies with the following directives:
73/23/CEE, 93/68/CEE, 89/336/CEE
92/31/CEE
and standards:
EN 60335, EN 61000, EN55014
The incoming water pressure must be
comprised between 0.5 and 8 bar (0.05 and
0.8 MPa).
Prepare wall couplings and ahead of them,
the appropriate cocks, which must not be
farther than the length of the pipes supplied.
If hot water is not available, mount a T pipe
on the cold water coupling. Then connect
both inlets to the cold water pipe.
Model Boiler capacity
Mod. 8 45 litres
Mod.11 58 litres
Mod.18 100 litres
Mod.26 146 litres
Mod.33 190 litres
When the connection is finished make sure
that the pipes are not crushed.
5.7 STEAM CONNECTION (steam-heated
machines only)
The washing machine is fitted with a 3/4"
steam inlet. The incoming steam pressure
must be between 0.5 and 6 bar (0.05 and 0.6
MPa). If doubts should arise, read the rating
plate data. Steam is considered as saturated
and dry.
The water in the tub is heated directly (not
through a coil, which would be indirect).
Therefore it will not be necessary to envisage
a condensation recovery coupling.
If the machine is liable to undergo ISPESL
inspection, keep all ISPESL documents in
the room where the washing machine is
lodged.
When the connection is finished be sure that
the pipe is not crushed.
5.8 DRAIN CONNECTION
Make certain that the distance between the
machine drain outlet and the floor drain is
not longer than the supplied drain elbow.
Water is drained through a motor-driven
valve that is open when the machine is not
supplied with electricity. Therefore the floor
drain must always be lower than the machine
drain outlet. The diameter of the floor drain
must never be smaller than that of the supplied
hose.
Model Flow rate of drain
Mod. 8 80 l/min
Mod.11 100 l/min
Mod.18 160 l/min
Mod.26 160 l/min
Mod.33 200 l/min
The draining pipe must resist 90
°
C.
Install a U-trap between the supplied hose
and the drain.
Check that the hose is not crushed.
5.9 AIR BREAK
The washing machine is equipped with an
air-break device to stop wastewater from
flowing back into the drinkable water system
7. INSTRUCTIONS FOR USE
7.1 OPERATION
Switch the appliance on by the main cut-off
switch on the wall.
Turn the machine main switch to position 1.
If the door is closed the door pilot light will
go on.
Check that the hot water, cold water and
steam taps are open (steam tap only on steam
heated machines).
Temperatures must be chosen according to
different types of fabrics. See symbols nor-
mally used in the textile industry, which are
commonly drawn on the labels attached to
fabrics.
Sort the laundry according to the type of
fabric. Press the door opening push button
(on models without handle) and load the
drum (see also paragraph 7.5).
Load the washing powder (foam damping
type) into the appropriate compartments
according to the cycle to be selected:
compartment A for pre-wash (if envisaged),
compartment B for wash, compartment C
for rinse liquid to be added during the last
rinse (see also paragraph 7.5).
Select the desired number of rinses.
Select the cycle that fits your laundry, then
press the green start push button and release
it: the machine will start working. If your
machine is equipped with coin meter, insert
the necessary coins: the machine will start
working.
At the end of the cycle the door pilot light
will be switched on again (see paragraph
7.2).
7.2 OPENING THE DOOR
The door pilot light goes on at the end of the
cycle. To open the door, hold the handle and
pull it while pressing the central push button.
The machine is fitted with an electronic
device that releases the door after 90 sec. in
the event of power failure. Take the lower
front panel off and pull the manual puller
downwards.
Before opening the door make sure that the
drum has come to a complete stop, that the
water has been drained and the temperature
is lower than 40
°
C.
7.3 REMOVE THE LID
To reach the machine electrical parts, take
off the screws fastening the back and soap
dispenser. Then lift the rear part of the lid
and pull it to the front by approximately 5
cm.
BEFORE TURNING THE MACHINE
ON BY THE CUTOFF SWITCH ON
THE WALL, PUT ALL THE PANELS
YOU HAVE REMOVED BACK IN
THEIR PLACE.
www.groupdynamics-laundry.com
sales@groupdynamics.lv