Graco VPM 12 Скачать руководство пользователя страница 49

Страница: 49 / 88

Maintenance

313875J

Advanced Display Module (ADM)

Replace Battery

A lithium battery maintains the ADM clock when power
is not connected.

To replace the battery:

Disconnect power to the ADM.

Remove rear access panel.

Remove the old battery and replace with a new
CR2032 battery.

Replace rear access panel.

Install Upgrade Token

See

Install Upgrade Tokens

on page 48.

Cleaning

Use any alcohol-based household cleaner, such as
glass cleaner, to clean the ADM. Spray on the rag then
wipe ADM. Do not directly spray the ADM.

Motor Control Module (MCM)

Keep heat sink fins clean at all times. Clean them using
compressed air.

NOTE:

Do not use conductive cleaning solvents on the

module.

Install Upgrade Token

See

Install Upgrade Tokens

on page 48.

Fluid Control Module (FCM)

Install Upgrade and Key Tokens

See

Install Upgrade Tokens

on page 48.

ti12903a

. 15: Clean Heat Sink Fins

r_257396_3b9905_02b

Heat
Sink Fins

Содержание VPM 12

























































































Результаты поиска

Содержание VPM 12

Отзывы:

Похожие инструкции для VPM 12

Бренды по названию

Популярные бренды

Graco VPM 12, Инструкция по эксплуатации

Результаты поиска

Содержание VPM 12

Отзывы:

Похожие инструкции для VPM 12

Бренды по названию

Популярные бренды