Graco VPM 12 Скачать руководство пользователя страница 74

Страница: 74 / 88

Appendix D - ADM Event and Error Codes Overview

313875J

P4D0

Pressure
Imbalance

The pressure difference
between the Red and Blue
material is greater than the
defined amount

Alarm

Dispense line is clogged

Ensure the material flow is equally restricted on both
material lines

Pressure imbalance is
defined too low

On the ADM go into the setup screens -> System->
and ensure the pressure imbalance value is the
maximum acceptable to prevent unnecessary alarms
which will abort dispenses

Orifice blocks closed off
too much on one or both
sides

Verify that one or both of the orifice blocks dispense
when adjusted to the fully open position then adjust
accordingly

Debris in the orifice block

Relieve system pressure then remove the orifice from
the orifice block and inspect for debris in the cavity

Material fillers may have
packed out in an orifice

Relieve system pressure and remove the orifice from
the orifice block and inspect for pack out. Clean or
replace as necessary.

Out of material

Fill tanks with material

Feed system defective

Replace defective item

P6A1

Red Pressure
Sensor Fault The pressure sensor is

providing invalid/no pressure
readings

Alarm

Loose/bad connection

Check to ensure the pressure transducer is properly
installed and all wires are properly connected

P6B2

Blue
Pressure
Sensor Fault

Alarm

Bad sensor

Replace pressure transducer

No material in pump

Fill tanks

T1A6

Red Tank
Low Fluid
Temp.

Fluid temperature is below the
defined low alarm limit

Alarm

Tripped circuit breaker

Visually check circuit breaker for a tripped condition

T1B5

Blue Tank
Low Fluid
Temp.

Alarm

T1A3

Red Inline
Low Fluid
Temp.

Alarm

T1B1

Blue Inline
Low Fluid
Temp.

Alarm

T1A2

Red Hose
Low Fluid
Temp.

Alarm

T1B4

Blue Hose
Low Fluid
Temp.

Alarm

Low power

Measure voltage across input terminals on power line
filter. Voltage should measure between 190 and 264
Vac

T1A7

Red Chiller
Low Fluid
Temp.

Alarm

Cable unplugged/loose
power

Check for loose or disconnected wires or plugs

T1B8

Blue Chiller
Low Fluid
Temp.

Alarm

Bad heater(s)

Measure resistance of heater(s)

T3H1

Oil Temp.
Cutback

The hydraulic oil temperature
is approaching a level where
damage is possible so the
Motor Control Module is
limiting the output to a safe
level

Deviation

No power to fan

Check cord to make sure fan has power

Debris in fan or fan grill

Clear debris from fan/fan grill

Low air volume from fan

Try to stop fan by lightly pressing on the center with a
pencil eraser. If the fan slows down easily it will need
to be replaced

T3N1

Motor Temp.
Cutback

Motor temperature is
approaching a level where
damage is possible so the
motor control module is limiting
the output to a safe level

Advisory

No power to fan

Check cord to make sure fan has power

Debris in fan or fan grill

clear debris from fan/fan grill

Low air volume from fan

Try to stop fan by lightly pressing on the center with a
pencil eraser. If the fan slows down easily it will need
to be replaced

Ambient environmental
conditions are too hot

Move machine to an area below 120°F

Motor/pump coupler may
be rubbing on hydraulic
pump

Reset coupler per specifications and retighten set
screws

Error
Code

Error Name

Error Description

Error
Type

Cause

Solution

Содержание VPM 12

























































































Результаты поиска

Содержание VPM 12

Отзывы:

Похожие инструкции для VPM 12

Бренды по названию

Популярные бренды

Graco VPM 12, Инструкция по эксплуатации

Результаты поиска

Содержание VPM 12

Отзывы:

Похожие инструкции для VPM 12

Бренды по названию

Популярные бренды