Graco Pro 230ES Скачать руководство пользователя | Manualshive

Страница: 20 / 46

background image

Drive Housing Replacement

20

3A2817A

Drive Housing Replacement

Removal

1.

Relieve pressure, page 9.

2.

Disconnect power cord from outlet.

3.

Remove screws (12) and pump rod cover (70).

4.

Remove pump, Displacement Pump Replacement,
page 17.

5.

Remove screws (12) from shroud (23).

6.

Remove screws (12) from front cover (22).

7.

Remove screws (47).

8.

Pull drive housing (42) off motor (54).

9.

Remove gear cluster (44) and (40) and thrust
washer (25) from drive housing.

Installation

1.

Apply a heavy coat of grease to gears and needle
bearing surfaces.

2.

Install washers (8, 10) on back of gear (40). Install
gear in motor end bell. Using grease for retention,
place washer (10) over bearing inside housing (42).

3.

Install washers (1, 9) on back of gear (44). Install in
motor endbell.

4.

Install thrust washer (25) on gear (44).

5.

Push drive housing (42) on motor endbell as you
guide gear crank (44) through hole in connecting
rod (43).

6.

Install screws (47).

7.

Install cover (22) and screws (12).

8.

Install shroud (23) and screws (12).

9.

Install pump; see Displacement Pump Replace-
ment, page 17.

10. Install pump rod cover (70) with screws (12).

NOTICE

Do not drop gear cluster (44) and (40) when remov-
ing from drive housing (42). Gear cluster may stay
engaged in motor front end bell or drive housing.

«
...
18
19
20
21
22
...
»

Содержание Pro 230ES















































Отзывы:

Нет отзывов

Похожие инструкции для Pro 230ES

Бренд: Berthoud Страницы: 36

Бренд: YATO Страницы: 76

Бренд: Gardenline Страницы: 2

Бренд: B&G Страницы: 2

Бренд: Coleman Страницы: 2

Бренд: EIC Страницы: 33

Бренд: DeVilbiss Страницы: 6

Бренд: Graco Страницы: 28

Бренд: Graco Страницы: 8

Бренд: Tidal Страницы: 8

Бренд: P.Lindberg Страницы: 50

Бренд: Binks Страницы: 8

Бренд: Graco Страницы: 24

Бренд: Graco Страницы: 80

Бренд: Caffini Страницы: 82

Бренд: NATI Страницы: 20

Бренд: California Air Tools Страницы: 9

Бренд: SAMES KREMLIN Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды