background image

Motor Brush Replacement 

24

3A2817A

Motor Brush Replacement

NOTE: 

Motors used in the Pro 270ES model sprayers 

are brushless. The following brush information and 
instructions apply to Pro 230ES model sprayers only.

Motor Brush Removal

Replace brushes worn to less than 1/2 in. Brushes wear 
differently on each side of motor, check both sides. 
Brush Repair Kit 287735 is available.

1.

Read 

General Repair Information

, page 10.

2.

Relieve pressure

, page 9.

3.

Unplug sprayer powercord.

4.

Remove motor shroud and two inspection covers 
(A).

5.

Push clip spring (B) to release hook (C) from brush 
holder (D). Pull out spring clip (B).

6.

Pull brush lead (E) off terminal (F). Remove brush 
(G).

7.

Inspect commutator for excessive pitting, burning, or 
gouging. A black color on commutator is normal. 
Have commutator resurfaced by a motor repair shop 
if brushes wear too fast.

Motor Brush Installation

1.

Install new brush (G) with lead into brush holder (D).

2.

Slide brush lead (E) onto terminal (F).

3.

Install spring clip (B). Push down to set hook (C) into 
brush holder (D).

4.

Repeat for other side.

5.

Test brushes.

a.

With sprayer OFF, turn pressure control knob 
fully counter-clockwise to minimum pressure. 
Plug in sprayer.

b.

Turn sprayer ON. Slowly increase pressure until 
motor is at full speed.

6.

Install brush inspection covers (A).

7.

Break in brushes

a.

Remove pump pin (32), Displacement Pump 
Replacement, page 17.

b.

Operate sprayer 1 hour with no load.

c.

Install pump pin (32). See 

Displacement Pump 

Replacement

, page 17.

ti7386b

A

ti7387a

1

F

E

G

B

3

C

2

D

1

Motor lead; do not disconenct

2

Minimum 0.5 in. (12.5 mm)

3

Included in Brush Repair Kit

NOTICE

When installing brushes, follow all steps carefully to 
avoid damaging parts.

NOTICE

Do not run sprayer for more than 30 seconds while 
checking brushes to avoid damaging displacement 
pump packings.

ti7388a

B

F

E

G

D

C

Содержание Pro 230ES















































Отзывы: