Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 2 / 98

Contents

3A9099A Operation, Repair, Parts

Contents

I mportant Grounding Information. . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Laser Information for Units with Laser Option. . 7

Tip Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Component Identification - LLV 200MMA . . . . . . . . . . . . . . . 9

Component Identification - Fusion MMA PC Gun. . . . . . . . 10

Piston Safety Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Loss of Air Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Theory of Gun Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Clear Spray Tip Adapter Clog. . . . . . . . . . . . . . . . . . . . . . 14

Clear Spray Tip Clogs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Assemble the Spray Gun . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setup Striper with Fusion MMA PC Gun . . . . . . . . . . . . . 16

Keep Components A and B Separate . . . . . . . . . . . . . . . 20

Changing Materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Gun Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Position Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Manual Guns Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Auto Guns Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Gun Positions Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Gun Arm Mounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Change Gun Position

(Front and Back) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Change Gun Position

(Left and Right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Trigger Sensor Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 25

Gun Cable Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Straight Line Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 27

Handle Bar Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Dot Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Daily shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

LineLazer V LiveLook Display . . . . . . . . . . . . . . . . . . . . . . . . 32

HP Auto Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Initial Setup (HP Auto Series) . . . . . . . . . . . . . . . . . . . . . . 33

Striping Mode (HP Auto Series) . . . . . . . . . . . . . . . . . . . . 35

Measure Mode (HP Auto Series) . . . . . . . . . . . . . . . . . . . 36

Layout Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Stall Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Angle Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Setup/Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Data Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Maintenance - Fusion MMA PC Gun . . . . . . . . . . . . . . . . . . 46

Flush Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Clean Spray Tip Adapter and Mix Chamber Nozzle. . . . . 47

Inspect the Check Valves. . . . . . . . . . . . . . . . . . . . . . . . . 48

Clean Mix Chamber Impingement Ports . . . . . . . . . . . . . 49

Remove the Fluid Cartridge . . . . . . . . . . . . . . . . . . . . . . . 49

Reinstall or Replace the PC Fluid Cartridge. . . . . . . . . . . 50

Inspect the Fluid Cartridge. . . . . . . . . . . . . . . . . . . . . . . . 51

Test Fluid Cartridge Restriction . . . . . . . . . . . . . . . . . . . . 51

Store the Fluid Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . 52

Clean Gun Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Clean Spray Tip Adapter . . . . . . . . . . . . . . . . . . . . . . . . . 52

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Inspect the Piston Safety Lock. . . . . . . . . . . . . . . . . . . . . 52

Remove/Reinstall Gun Fluid Manifold . . . . . . . . . . . . . . . 53

Clean Gun Fluid Manifold. . . . . . . . . . . . . . . . . . . . . . . . . 53

Clean Passages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Clean Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Remove and clean Muffler with acetone. . . . . . . . . . . . . . 54

Inspect the Piston. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Inspect the Air Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Disassemble Front End of Fusion MMA PC Gun . . . . . . . 56

Reassemble Front End of Fusion MMA PC Gun . . . . . . . 56

Maintenance - LineLazer V 200MMA 1:1 . . . . . . . . . . . . . . . 57

Recycling and Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Rechargeable Battery Disposal . . . . . . . . . . . . . . . . . . . . 58

End of Product Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Hydraulic Oil/Filter Change. . . . . . . . . . . . . . . . . . . . . . . . . . 59

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Gun Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Drill Bit Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Drill Bit Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Air Purge Handle Cleanout Drill Kit . . . . . . . . . . . . . . . . . 68

LineLazer V 200MMA 1:1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Component Parts Drawings. . . . . . . . . . . . . . . . . . . . . . . 69

Parts Drawing - Frame Assembly. . . . . . . . . . . . . . . . . . . . . 70

Parts List - Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . 71

Parts Drawing - Gun Arm & Gun Trigger . . . . . . . . . . . . . . . 72

Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Gun Holder and Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Gun Trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Parts Drawing - Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Parts List - Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Detail Views - Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

P arts Drawing - Handle/Controls . . . . . . . . . . . . . . . . . . . . . 78

Parts List - Handle/Controls . . . . . . . . . . . . . . . . . . . . . . . . . 79

Parts Drawing - Filters A & B . . . . . . . . . . . . . . . . . . . . . . . . 80

Parts List - Filters A & B . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Parts Drawing - Fluid Pumps A & B . . . . . . . . . . . . . . . . . . . 82

Parts List - Fluid Pumps A & B . . . . . . . . . . . . . . . . . . . . . . . 83

Parts Drawing - Engine & Compressor . . . . . . . . . . . . . . . . 84

Parts List - Engine & Compressor . . . . . . . . . . . . . . . . . . . . 85

Parts Drawing - EZ AlignTM Swivel Wheel . . . . . . . . . . . . . 86

Parts List - EZ Align Swivel Wheel . . . . . . . . . . . . . . . . . . . . 87

Parts Drawing - Pressure Tank. . . . . . . . . . . . . . . . . . . . . . . 88

Parts List - Pressure Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Gun Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Stainless Steel Side Seal Kits . . . . . . . . . . . . . . . . . . . . . 90

Polycarballoy Side Seal Kits . . . . . . . . . . . . . . . . . . . . . . 90

Gun Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Lubricant for Gun Rebuild . . . . . . . . . . . . . . . . . . . . . . . . 90

Grease Cartridge for Gun Shutdown . . . . . . . . . . . . . . . . 90

Flushing Manifold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Solvent Flush Canister Kit . . . . . . . . . . . . . . . . . . . . . . . . 90

Solvent Flush Pail Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Gun Cleaning Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Check Valve Filter Screen Kits . . . . . . . . . . . . . . . . . . . . . 91

Drill Bit Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Handle Cleanout Drill Kit . . . . . . . . . . . . . . . . . . . . . . . . . 91

Acceptable Cartridge Storage Liquids. . . . . . . . . . . . . . . 91

Cartridge Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Fusion PC Cartridge Tools . . . . . . . . . . . . . . . . . . . . . . . . 91

MMA Static Mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

World Symbol Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Technical Specifications - Gun. . . . . . . . . . . . . . . . . . . . . . . 95

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды