Graco LineLazer V 200MMA Скачать руководство пользователя страница 48

Страница: 48 / 98

Maintenance - Fusion MMA PC Gun

3A9099A Operation, Repair, Parts

Inspect the Check Valves

1. Follow the

Pressure Relief Procedure

, page 14.

2. Follow

Flush Gun

, page 47, to remove residual

chemical.

3. Remove the Gun Fluid Manifold (12), see

Clean

Passages

, page 54. Leave air connected.

Clean

Gun Fluid Manifold

, page 53.

4. Shut off air.

5. Pry out check valves (26) at notch.

6. Slide filter (26d) off. Clean and inspect parts.

Thoroughly inspect o-rings (26f, 26g). If necessary,

remove screw (26b) and disassemble entire check

valve.

7. Reassemble check valves. Screw (26b) should be

flush (within 1/16 in. or 1.5 mm) of housing (26a)

surface. Liberally lubricate o-rings (26f, 26g) and

carefully reinstall in fluid housing.

8. Attach the Gun Fluid Manifold, see

Clean

Passages

, page 54. Connect air. Return gun to

service.

NOTICE

To prevent cross-contamination in the gun, do not

interchange A component and B component parts.

Cross-contamination can result in cured material in the

gun. Cured material may damage the sealing surfaces,

block fluid passages, and prevent gun function.

Damaged check o-rings (26f, 26g) may result in

external leakage. To avoid potential leakage and

serious injury from skin injection, replace any

damaged o-rings.

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Бренды по названию

Популярные бренды