Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 24 / 98

Startup

3A9099A Operation, Repair, Parts

Gun Arm Mounts

This unit is equipped with front and rear gun arm

mounts to allow the operator to place the guns in the

optimal location.

Change Gun Position

(Front and Back)

1. Loosen gun arm knob and remove from gun arm

mounting slot.

2. Slide gun arm assembly (including gun and hoses)

out from gun arm mounting slot.

3. Slide gun arm assembly into desired gun arm

mounting slot.

4. Tighten gun arm knob into gun arm mounting slot.

Change Gun Position

(Left and Right)

Removal

1. Loosen vertical gun arm knob on gun arm mounting

bar and remove.

2. Extend mounting bar on opposite side of the

machine.

ti27796a

ti27797a

NOTICE

Make sure all hoses, cables, and wires are properly

routed through brackets and do NOT rub on tire.

Contact with tire will result in damaged hoses, cables,

and wires.

ti27798a

ti27799a

ti27800a

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды