Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 56 / 98

Maintenance - Fusion MMA PC Gun

3A9099A Operation, Repair, Parts

Disassemble Front End of

Fusion MMA PC Gun

1. Follow the

Pressure Relief Procedure

, page 14.

2. Follow

Flush Gun

, page 47.

3. Unscrew Lock Ring (15) until front end of gun is

loose. Turn Fluid Housing (6) 1/8 turn

counterclockwise. Unscrew lock ring completely

and remove front end of gun.

Reassemble Front End of Fusion

MMA PC Gun

1. Engage the Piston Safety Lock (11). See

Piston

Safety Lock

, page 11.

2. Push on Spray Tip Adapter (3) until it is flush with

front of gun. This ensures that mix chamber is all

the way back.

3. Check that o-ring (21) is in position (Reference

Parts Drawing - Gun

, page 74). Liberally lubricate

o-ring, threads of Lock Ring (15) and handle (H),

and outside of lock ring. Orient Fluid Housing (6) as

required for desired fluid manifold mounting

(bottom mounting is shown).

4. Insert keyed end of Mix Chamber (13) in socket (X).

Screw lock ring onto handle as far as possible by

hand.

5. Turn Fluid Housing (6)1/8 turn clockwise to engage

slots (Y) and tabs (Z). Push on front end to ensure it

is properly seated. Continue screwing Lock Ring

(15) onto handle (H) very securely. When properly

assembled, lock ring is snug against handle.

NOTICE

If Lock Ring (15) is stuck due to material buildup, do

not force it by turning entire front end. Locating tabs

may break off. Soak front of gun in solvent to soften

cured material and free lock ring.

Improper attachment of the front end may result in

serious injury from skin injection. To avoid injury,

check that the front end is securely attached and the

lock ring is snug against the handle before gun

operation.

TI2416A

TI2409A

TI2416A

TI2423A

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды