Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 31 / 98

Cleanup

3A9099A Operation, Repair, Parts

Daily shutdown

1. Perform

Pressure Relief Procedure

, page 14.

2. Close Fluid Valves A and B on the hose manifold

with the provided 5/16” nut driver.

3. Leave Purge Air Valve turned on and gun

detriggered while machine is still running.

NOTE:

Grease gun daily to prevent two component

curing and keep fluid passages clean. Purge air carries

grease mist through air chamber (AC), impingement

ports (IP), and out mix chamber nozzle (N), coating all

surfaces. Use Graco 117773 Grease, see page 90.

NOTE:

Flow paths are not shown to scale, for clarity.

See Parts List, pages 74-75, for part numbers and

reference locations.

Key

4. Remove Grease Fitting cap (37). Using grease gun,

dispense grease into fitting (25) until grease mist

sprays from mix chamber nozzle (N). Do not

over-grease; use 2 shots maximum. Do not spray

grease mist on sprayed material.

5. Replace grease cap (37).

Purge Air

Fluid

Cleanoff Air

Grease

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды