Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 65 / 98

Gun Troubleshooting

3A9099A Operation, Repair, Parts

Gun

Troubleshooting

1. Follow the

Pressure Relief Procedure

, page 14,

before checking or servicing the gun.

2. Check all possible problems and causes before

disassembling the gun.

NOTICE

To prevent cross-contamination in the gun, do not

interchange A and B component Methyl-Methacrylate

(MMA). Cross-contamination can result in cured

material in the gun. Cured material may damage the

sealing surfaces, block fluid passages, and prevent

gun function.

Problem

Cause

Solution

Gun does not fully actuate

when triggered

The safety lock is engaged.

Disengage safety lock. See

Piston Safety

Lock

, page 11.

The muffler is plugged.

Clean the muffler. See

Clean Muffler

, page 54.

The air valve o-rings are damaged.

Replace the air valve o-rings. See

Inspect the

Air Valve

, page 55.

Cured material is inside the cartridge.

Inspect the fluid cartridge and mix chamber

for scratches. See

Inspect the Fluid

Cartridge

, page 51. Replace.

The retaining ring is not bottomed out.

Tighten retaining ring until bottomed out.

Fluid does not spray when the

gun is fully actuated

The fluid valves are closed.

Open the fluid valves.

The impingement ports are plugged.

Clean the impingement ports. See

Clean Mix

Chamber Impingement Ports

, page 49 .

The check valves are plugged.

Clean the check valves. See

Inspect the

Check Valves

, page 48.

The cartridge is plugged.

Remove the Fluid Cartridge

, page 49, then

Test Fluid Cartridge Restriction

, page 51

Gun actuates slowly

The muffler is plugged.

Clean the muffler. See

Clean Muffler

, page 54.

The piston o-rings are damaged.

Replace the piston o-rings. See

Parts

Drawing - Gun

, page 74.

The air valve is dirty, or the o-rings are

damaged.

Clean air valve or replace o-rings. See

Inspect

the Air Valve

, page 55.

Gun delays, then actuates

abruptly.

Chemical or material has cured around the

side seals in the fluid cartridge.

See

Inspect the Fluid Cartridge

, page 51.

Replace.

The retaining ring is not bottomed out.

Tighten retaining ring until bottomed out.

Cured material is inside the cartridge.

Inspect the fluid cartridge and mix chamber for

scratches. See

Inspect the Fluid Cartridge

page 51. Replace.

The retaining ring is not bottomed out.

Tighten retaining ring until bottomed out.

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды