Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 51 / 98

Maintenance - Fusion MMA PC Gun

3A9099A Operation, Repair, Parts

Inspect the Fluid Cartridge

If the gun does not spray chemical, or only sprays one

chemical when triggered, inspect the PC Fluid

Cartridge for reacted chemical on the side sealing

surfaces.

•

If reacted chemical is found near the side seals

Replace the fluid cartridge. Follow

Assemble the

Spray Gun

, page 15.

•

If no reacted chemical is found near the side

seals

: Follow

Test Fluid Cartridge Restriction

page 51.

Test Fluid Cartridge Restriction

If no reacted chemicals are found on the fluid cartridge,

test the fluid cartridge restriction with the Grease Tool (21).

1. Insert Divider Tool (22) from the back of the PC

Fluid Cartridge (20) so that it sits upright. The

Divider Tool (22) prevents chemical from reaching

the opposite side seal.

2. Guide the Grease Tool (21) over the B side fluid port

and pump grease.

•

If grease purges out of the internal side seal:

obstruction or restriction is in the flow path and the

cartridge should be reused.

•

If the grease tool is forced backward off of the

fluid port:

The flow path is restricted and the

cartridge should be replaced.

3. Remove and clean the Grease Tool (21) to prevent

contamination and repeat previous step for the A

side.

4. Remove the Grease Tool (21) and Divider Tool (22).

Clean and store for the next use.

5. Follow

Assemble the Spray Gun

, page 15, to

replace or reinstall the fluid cartridge and prepare

the gun to spray.

NOTICE

To prevent cross-contamination in the gun, do not

interchange A component and B component parts.

Cross-contamination can result in cured material in the

gun. Cured material may damage the sealing surfaces,

block fluid passages, and prevent gun function.

ti37616a

WLD

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды