Graco LineLazer V 200MMA Скачать руководство пользователя

Страница: 62 / 98

Troubleshooting

3A9099A Operation, Repair, Parts

Excessive leakage around

hydraulic motor piston rod

wiper.

Piston rod seal worn or damaged.

Replace these parts.

Fluid delivery is low.

Pressure setting too low.

Increase pressure.

Displacement pump outlet filter (if used) is

dirty or clogged.

Clean filter.

Intake line to pump inlet is not tight.

Tighten.

Hydraulic motor is worn or damaged.

Bring sprayer to Graco distributor for repair.

Large pressure drop in fluid hose.

Use larger diameter for shorter hose.

The sprayer overheats.

Paint buildup on hydraulic components.

Clean.

Oil level is low.

Fill with oil.

Excessive hydraulic pump

noise.

Low hydraulic fluid level.

Shut off sprayer. Add fluid.

Gallon (liter) counter not

adding fluid volume.

Fluid pressure not high enough.

Must be over 800 psi (55 bar) for counter to

add.

Broken or disconnected pump counter wire,

both pumps.

Check wires and connections. Replace any

broken wires

Missing or damaged magnet.

Reposition or replace magnet on pump, see

Parts manual (Pump parts) for magnet

location.

Bad sensor, both pumps.

Replace sensor.

Sprayer operates, but

display does not.

Bad connection between control board and

Display.

Remove Display and reconnect.

Display damaged.

Replace Display.

Distance not adding properly

(Measure mode will be

inaccurate and speed will be

wrong).

Machine not calibrated.

Perform calibration procedure.

Rear tire pressure is too low or too high.

Adjust tire pressure to 55 +/- 5 psi (380 +/-

34kPa).

Gear teeth missing or damaged (right side

when standing on platform).

Replace distance gear/wheel hub.

Distance sensor is loose or broken.

Reconnect or replace sensor.

Mils not calculating or

calculates wrong.

Distance sensor.

See “Distance counter not operating

properly”.

Gallon counter.

See “Gallon (liter) counter not adding fluid

volume.”

Line width not entered.

Set line width on main striping screen.

Bad or damaged control board.

Replace control board.

Fluid spray starts after spray

icon is shown on Display.

Interrupter is improperly positioned.

Turn screw counterclockwise until spray icon

synchronizes with fluid spray, page 25.

Spray icon does not show on

Display when fluid is

sprayed.

Loose connector.

Check that 5-pin connector and reed switch

are properly connected.

Interrupter is improperly positioned.

Turn screw counterclockwise until spray icon

synchronizes with fluid spray, page 25.

Problem

Cause

Solution

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды