Graco LineLazer V 200MMA Скачать руководство пользователя страница 66

Страница: 66 / 98

Gun Troubleshooting

3A9099A Operation, Repair, Parts

Problem

Cause

Solution

Loss of round pattern.

The mix chamber nozzle is dirty.

Clean the mix chamber nozzle. See

Clean

Spray Tip Adapter and Mix Chamber

Nozzle

, page 47.

Loss of flat pattern.

The spray tip is plugged.

Clean in compatible solvent.

Clean Spray Tip

Adapter and Mix Chamber Nozzle

, page 47

The tip is worn.

Replace the flat spray tip.

The mix chamber nozzle is dirty.

Clean the mix chamber nozzle. See

Clean

Spray Tip Adapter and Mix Chamber

Nozzle

, page 47

Leakage between flat tip and

mix chamber.

The tip is not seated properly.

Reassemble. See

Clean Spray Tip Adapter

and Mix Chamber Nozzle

, page 47.

The o-ring s damaged or missing.

Replace the flat spray tip o-ring.

Pressure imbalance.

The impingement ports are plugged.

Clean the impingement ports. See

Clean Mix

Chamber Impingement Ports

, page 49.

The check valves are plugged.

Clean the check valves. See

Inspect the

Check Valves

, page 48.

The viscosities not equal.

Adjust temperature to compensate.

The cartridge is plugged.

Remove the Fluid Cartridge

, page 49, then

Test Fluid Cartridge Restriction

, page 51.

A and/or B fluid inside of the

cartridge.

The side seals in the fluid cartridge are

damaged.

Replace. See

Inspect the Fluid Cartridge

page 51.

The mix chamber is damaged.

Replace. See

Remove the Fluid Cartridge

page 49.

The side seal o-rings in the fluid cartridge are

damaged.

Replace the fluid cartridge. See

Inspect the

Fluid Cartridge

, page 51.

The spray tip adapter is tightened while the

fluid valves are open.

Close valves first.

Fluid mist from mix chamber

or spray tip adapter.

The side seals in the fluid cartridge are

damaged.

Replace. See

Inspect the Fluid Cartridge

page 51.

The side seal o-rings in the fluid cartridge are

damaged.

Replace the side seal o-rings.

Inspect the

Fluid Cartridge

, page 51.

The mix chamber is damaged.

Replace the mix chamber. See

Remove the

Fluid Cartridge

, page 49.

Excessive overspray.

Too much cleanoff air.

Reduce cleanoff air.

Rapid buildup of material on

spray tip adapter.

The spray tip adapter holes are plugged.

Clean the spray tip adapter holes. See

Clean

Spray Tip Adapter

, page 52.

Too little cleanoff air.

Increase cleanoff air.

The fluid cartridge front o-ring is damaged or

missing.

Replace the fluid housing o-ring. See

Parts

Drawing - Gun

, page 74.

The front o-ring is damaged.

Replace the front o-ring. See

Parts Drawing -

Gun

, page 74.

Reduced cleanoff air.

The front o-ring is damaged.

Replace the front o-ring. See

Parts Drawing -

Gun

, page 74.

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды