Graco LineLazer V 200MMA Скачать руководство пользователя страница 35

Страница: 35 / 98

LineLazer V LiveLook Display

3A9099A Operation, Repair, Parts

Striping Mode (HP Auto Series)

Operating in Striping Mode

Striper must be running before activating gun trigger

control.

1. Make sure engine is running.

2. Use gun activation buttons to select guns and line

type.

3. Press gun trigger control to begin spraying.

In Automatic Mode or Semi-Automatic Mode the

will flash when gun trigger control is pressed to

signal mode is active.

Ref.

Description

Select

a “Favorite”, press for less than one second.

Save

a “Favorite”, press and hold for more than three

seconds.

Cycles between viewing line width or paint and space

value.

Cycles between Manual Mode, Semi-Automatic

Mode, Automatic Mode.

Manual Mode

Press and hold gun trigger

control to stripe.

Semi-Automatic Mode

Press and release gun

trigger control to stripe the programmed length one

time when in Skip Mode.

Automatic Mode

Press and release gun trigger

control to start striping. Press and release button

again to stop.

Resets trip distance.

Job Data Logger, page 45.

Scrolls between menu screens.

Paint and Space length

line width adjustment

buttons.

Auto guns activation buttons.

MIL thickness. While spraying “Instant MIL avg” is

displayed. When stopped total “Job MIL avg” is

displayed.

Total gallons (liters) sprayed, Pump A and B

Total line length sprayed.

Pressure, Pump A and B

ti27893a

ti27881a

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Похожие инструкции для LineLazer V 200MMA

Бренды по названию

Популярные бренды