Graco LineLazer V 200MMA Скачать руководство пользователя страница 34

Страница: 34 / 98

LineLazer V LiveLook Display

3A9099A Operation, Repair, Parts

3. Press

to select Setup/Information.

4. Press

for Calibration. Set TRAVEL DIST to 25 ft

(7.6m) or longer. Longer distances ensure better

accuracy, depending on conditions.

5. Turn on laser and align laser dot with 1 foot

(30.5cm) on steel tape.

6. Press and release gun trigger control to start

calibration.

7. Move striper forward. Keep laser dot on steel tape.

8. Stop when laser aligns with 26-ft (8m) or distance

entered on steel tape (25-ft / 7.6m distance).

9. Press and release gun trigger control to complete

calibration.

• Calibration is not complete when the exclamation

symbol

is displayed.

• Calibration is finished when the check mark symbol

is displayed.

10. Calibration is now complete.

Go to

Measure Mode (HP Auto Series)

, page 36, and

verify accuracy by measuring the tape.

ti35233a

CALIBRATION

SETTINGS

INFORMATION

ENG SPA FRE DEU RUS WORLD

LAYOUT MODE

ti27912a

Содержание LineLazer V 200MMA



































































































Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Бренды по названию

Популярные бренды

Graco LineLazer V 200MMA, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineLazer V 200MMA

Отзывы:

Бренды по названию

Популярные бренды