background image

GPS1195 Auto Gate Manual                                                                              Version 3 

Installation Set Up 

Installation of all equipment should be performed by trained personnel, skilled in the type of work 
involved. All installations should be inspected by appropriate authorities, or a factory trained 
representative, before the system is put into operation.  

Note: 

    

Do not remove the plastic bag from the piece of equipment until the unit is placed in the 

correct location according to the information tag attached to the top of the plastic bag. Refer to your 
layout drawings for correct equipment placement 

1)

 

Remove packaging carefully so as not to damage the paint finish 

2)

 

Unlock & Remove the door 

3)

 

Carefully place the gate in the correct position and mark 4 mounting holes on the concrete 

4)

 

Carefully remove the gate and drill holes suitable for 3/8” x 4” lag bolts.  

5)

 

Place the gate back in position and install bolts and flat washers, lubricate bolts with grease 
when installing 

6)

 

Attach wiring to correct terminals according to field connection drawings supplied. Wiring 
and connector terminals and techniques used must be done according to standard electrical 
codes or statues. Particular attention must be paid to proper grounding. Low voltage circuits 
are class 1 and should be installed accordingly.  

7)

 

Connect each gate to a dedicated 15 AMP, 120Vac circuit breaker. Ensure the complete 
electrical installation is done according to all local Codes / Regulations. 

8)

 

The Gate shall be Powered and Protected through an Approved Ground Fault Circuit 
Interrupter ( GFCI ) at the time of Installation 

9)

 

Door lock keys are attached to the outside of the flange 

10)

 

Limit cam adjustment may be necessary to level the barrier arm in the field. Loosen the wing 
nut that keeps the cam in place and move the cam forward or backwards slightly to level the 
arm properly. Fully re-tighten the cams with the wing nuts when finished.  

11)

 

For the vertical up position of the barrier arm, 

do not adjust with the UP limit cam

. Loosen 

the 2 nuts found on the connecting rod which has one left hand and one right hand eye bolt 
at the top and the bottom of the rod. At the center of the Rod is a flat point. Use a ½” open 
end wrench to turn the connecting rod either left or right until the vertical position of the 
arm is correct. Fully tighten the 2 nuts, each one against an eye bolt. 

12)

 

For barrier arms longer than 14ft, the internal counter balance spring may require a slight 
adjustment in order to balance the arm for a smooth open, close operation of the arm. This 
only applies to newly installed gates 

13)

 

The gear reducer has a pin in the breather plug that is there for transport only so that oil 

does not leak out. This pin must be removed when the gate is to go into operation. 

Page 4A 

Содержание GPS1195





























Отзывы: