manualshive.com logo in svg

Gotting HG G-73650-A, Основы, пусконаладка и программное обеспечение

Поделиться
Скачать
Gotting HG G-73650-A Скачать руководство пользователя страница 64

Commissioning

HG G-73650-A

English, Revision 07, Date: 07.03.2018

63

4.11.8

(H) Vehicle Specials

This output is vehicle specific. Information is available in the reference manual.

4.11.9

(I) Datalogging (Parameterization of the output) 

In this menu the debugging outputs of the steering controller and the sensor fusion

 

can be parameterized. The indicated menu items function only as titles for a different 
number of issued variables. These various options are necessary as it would last more

 

than 50 ms to issue all variables - this would be too time consuming for the system

 

function. On the other hand failures of different types each require individual variables. 
Allocation of the variables characterized by a header field with their corresponding

 

names can be taken from the CSV- file.

M

Secondary ONS Typ

Secondary odometry is compared to primary odometry. Should 
large differences between primary and secondary odometry arise 
(see D, E and F), the accuracy of the internal sensor fusion will be 
set to a poor value and the vehicle stops. Therefore defective sen-
sors can be detected.

N

Delta Posi. Max P

Maximum permissible differencebetween odometry based 
transponder positions and the positions provided in the transponder 
list in percent. 

O

Transp. Ant. Typ

Types of transponder antennas:
-

G 71720: Used for track guidance (lateral displacement will be 
measured)

-

G 98767: Not suitable for track guidance (lateral displacement 
will not be measured). For this antenna an additional guidance 
or camera system has to be applied.

P

Skalierung Sky T.

The Sky-Trax system specifies exact locations of the tags in pixels. 
This parameter provides a conversion between pixels and meters. If 
there are different tag sizes or different heights, a fine tuning adjust-
ment is possible with the tag sizes of the transponder list.  

Key

Name

Description

Table 38

Parameters Navigation > Sensor Fusion (part 2 of 2)

Содержание HG G-73650-A













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды