Gotting HG G-73650-A Скачать руководство пользователя страница 62

Страница: 62 / 76

Commissioning

HG G-73650-A

English, Revision 07, Date: 07.03.2018

4.11.7

(G) Sensor Fusion

Figure 29

Screenshot: Parameters Navigation > Sensor Fusion

The different parameters are described in the following table:

Typ

Controller Type: Should always be set to 0 (PID controller with
parameterizable parts (see point A - D))

Ringspeicher Peri

Time delay for the cyclic buffer of the velocity estimator (not requi-
red for controller type 0)

Wert Schaetzer

Expected value of the velocity estimator (not required for controller
type 0)

Differenz Eingriff

Difference between nominal and actual value activating an incre-
ased influence of the controller (not required for controller type 0)

Zu hoch Wert

Velocity difference activating brake control (not required for cont-
roller type 0).

Zu hoch Perioden

Number of periods that have to be too high until the brakes are
engaged

Rampe

For some vehicle options velocity is output via a velocity ramp func-
tion. This parameter corresponds to the increment by which the tar-
get velocity shall be incremented or decremented every 50ms.

V Max Vorwaerts

Limitation of the forward speed for those vehicles using a velocity
ramp.

Key

Name

Description

Table 37

Parameters Navigation > Speed Controller (part 2 of 2)

Main Menue -> Parameter Menue -> Sensorfusion Variables

A: Min Dist. Reading (current: 0.300000 [ m ] )

B: Min Dist. Single (current: 0.500000 [ m ] )

C: Max Dist. Double (current: 0.000000 [ m ] )

D: Delta Angle Max (current: 400.000000 [ ¯ ] )

E: Delta X Pos Max (current: 10000.000000 [ m ] )

F: Delta Y Pos Max (current: 10000.000000 [ m ] )

G: Delta Posi. Max (current: 0.100000 [ m ] )

H: Max Tol. Tr/ONS (current: 0.100000 [ m ] )

I: Single Antenna (current: On )

J: Single Ant.op.Dir.(current: On )

K: Gyro (current: On )

L: Primary ONS Typ (current: 2 )

M: Secondary ONS Typ (current: 2 )

N: Delta Posi. Max P (current: 0.000000 )

O: Transp. Ant. Typ (current: HG 71720 )

P: Skalierung Sky T. (current: 0.000000 )

[ESC] -> back/cancel

Содержание HG G-73650-A













































































Результаты поиска

Содержание HG G-73650-A

Отзывы:

Бренды по названию

Популярные бренды

Gotting HG G-73650-A, Основы, пусконаладка и программное обеспечение

Результаты поиска

Содержание HG G-73650-A

Отзывы:

Бренды по названию

Популярные бренды