manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Pioneer Peak 1500DW Скачать руководство пользователя страница 98

STEP 37:  PICNIC TABLE

1:   MEASURE 26-3/8" FROM THE BOTTOM OF THE CORNER POSTS ON THE RIGHT SIDE OF THE PLAYSET.  MAKE MARKS 

ON THE INSIDE OF THE CORNER POSTS WITH A PEN OR PENCIL AT 26-3/8".
2:   PLACE THE TOP OF THE RIGHT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT FRONT CORNER POST.  ATTACH 

THE RIGHT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.
3:  PLACE THE TOP OF THE LEFT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT REAR CORNER POST.  ATTACH THE 

LEFT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

NOTE: RAMP AND ROCK WALL 

REMOVED FOR CLARITY.

 26-3/8" 

LEFT SIDE ASSEMBLY

(LEG ON INSIDE)

RIGHT SIDE ASSEMBLY

(LEG ON INSIDE)

#8 X 3" 

WOOD SCREW

88

Содержание Pioneer Peak 1500DW





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды