Gorilla Playsets Pioneer Peak 1500DW Скачать руководство пользователя страница 5

Страница: 5 / 188

IMPORTANT SAFETY GUIDELINES

This product is recommended for use by children ages 3-11. This product is intended

for residential use only and not intended for use in any public setting. A safety surface

such as mulch or recycled tire should be used under the play set to prevent injury from

falls. Also a 6 foot safety zone should be used around the entire play set.

As with any home project, good judgment and respect for power tools will greatly

reduce the risk of injury. Gorilla recommends you follow all tool manufacturers’ safety

guidelines. Always wear eye protection and safety gloves to prevent injury. In several

phases of construction two people may be required for lifting and securing of lumber.

While the play set is being constructed, please keep children off the equipment until the

project is complete. Bolts and screw heads should be checked regularly for tightness.

The ground ladder, rope ladder, slide, swings and other areas where children spend a

majority of their playtime should be checked more frequently.

Gorilla shall not be liable for incidental, indirect or consequential damages or

injuries that result from building and/or playing on our play sets. Adult supervision is

recommended anytime a play set is being used.

WEIGHT LIMITS FOR GORILLA PLAYSETS

• FORT PLATFORMS: 800 LBS. TOTAL WEIGHT

• SWING BELT: 225 LBS.

• TANDEM SWINGS: 70 LBS. PER CHILD. UP TO 140 LBS. TOTAL WEIGHT.

• TRAPEZE: 125 LBS.

• FULL BUCKET SWING/ HALF BUCKET SWING: 50 LBS.

• HEAVY DUTY TODDLER BUCKET SWING: 85 LBS.

• INFANT SWING: 35 LBS.

• TIRE SWING: 125 LBS. TOTAL WEIGHT

• ROPE LADDER: 75 LBS.

• ROCK WALL: 150 LBS.

• CLIMBING RAMP: 150 LBS.

• MONKEY BARS: 175 LBS.

• ALL SLIDES: 150 LBS.

Gorilla recommends that the weight limits for all components must not be exceeded.

Failure to adhere to these and other safety guidelines could result in damage to the play

set and injury to the users.

Содержание Pioneer Peak 1500DW





























































































































































































Результаты поиска

Содержание Pioneer Peak 1500DW

Отзывы:

Бренды по названию

Популярные бренды

Gorilla Playsets Pioneer Peak 1500DW, Руководство пользователя

Результаты поиска

Содержание Pioneer Peak 1500DW

Отзывы:

Бренды по названию

Популярные бренды