manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Pioneer Peak 1500DW Скачать руководство пользователя страница 65

STEP 12:  ROCK WALL

1:  FIND ELEVEN 5/4 X 6 X 23-7/8" ROCK WALL BOARDS, AND ONE 5/4 X 6 X 23-7/8" BOTTOM ROCK WALL BOARD(1 

HOLE).
2:  STARTING FROM THE TOP, PLACE ONE ROCK WALL BOARD ON TOP OF THE ROCK WALL SIDES, FLUSH TO THE TOP 

OF THE ROCK WALL SIDES, AND ATTACH WITH TWO 2" WOOD SCREWS IN EACH SIDE.
3:  CONTINUE DOWN THE ROCK WALL WITH THE REMAINING ROCK WALL BOARDS, FASTENING EACH BOARD WITH 

TWO 2" WOOD SCREWS ON EACH END.
4:  THE FINAL BOARD WILL BE THE BOTTOM ROCK WALL BOARD WITH ONE HOLE.  ATTACH WITH TWO 2" WOOD 

SCREWS PER SIDE.
5:  IN SOME CASES, THERE WILL BE EXCESS LENGTH ON THE ROCK WALL SIDES.  THIS IS DUE TO MILLING VARIATIONS, 

AND IS ALSO USED TO HELP LEVEL THE ROCK WALL SIDES ON UNEVEN GROUND.
6:  ROCK WALL SIDES MAY NOT BE EVEN WITH THE BOTTOM ROCK WALL BOARD DUE TO MILLING VARIATIONS AND 

WOOD SHRINKAGE.

2" WOOD SCREW

5/4 X 6 X 23-7/8" 

BOTTOM ROCK 

ROCK WALL BOARD

5/4 X 6 X 23-7/8" 

WALL BOARD

TOP IS FLUSH TO 

ENDS OF SIDES.

55

Содержание Pioneer Peak 1500DW





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды