manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Pioneer Peak 1500DW Скачать руководство пользователя страница 164

ALIGN EDGE OF BORDER UNDER THE DECK 

5) It will be very helpful to have an assistant at this stage. We recommend predrilling holes for the screws on the 

Have your assistant push down on the board while you install a pan head screw and washer into the hole.  Go 

bridge deck boards.  Mark through the center grommet onto the deck board.  Drill a 1/8" hole by 1" deep.  

bottom of the deckboards fastened to the chains.    Align the edge of the mesh border with the end of the 

go from the center grommet to the other side and do the same.

from the center grommet to one end of the mesh and repeat the mark/drill/install fasteners procedure.  Then 

BOARDS THAT ARE FASTENED TO THE CHAINS.

WITH THE END OF THE 2 X 4 BRIDGE DECK 

MARK THROUGH THE CENTER OF THE CENTER 

GROMMET ONTO THE MIDDLE DECK BOARD.

DRILL A 1/8" X 1" DEEP HOLE AT THE MARK.  

PLACE A PAN HEAD SCREW THROUGH A 

WASHER AND INSTALL INTO THE HOLE.

TRY TO CENTER THE WASHER ONTO THE 

GROMMET BEFORE TIGHTENING COMPLETELY.

Example picture of the completed 

Clatter Bridge Mesh Panels.

Содержание Pioneer Peak 1500DW





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды