manualshive.com logo in svg

Gorilla Playsets Pioneer Peak 1500DW, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets Pioneer Peak 1500DW Скачать руководство пользователя страница 62

STEP 9: CENTER DECK SUPPORT

1: FIND THE 2 X 4 X 70" CENTER DECK SUPPORT WITHOUT HOLES.
2: FROM THE UNDERSIDE OF THE DECK SPACERS THAT WERE PREVIOUSLY INSTALLED, PLACE THE CENTER DECK 

SUPPORT AT THE CENTER OF THE DECK SPACERS (USE THE HOLE ON CENTER AS A GUIDE) AND MAKE A MARK ON 

THE OUTSIDE OF THE FORT TO REPRESENT A CENTER LINE.
3: USE 2" WOOD SCREWS TO ATTACH THE DECK SPACERS TO THE CENTER DECK SUPPORT.
4: CENTER THE 2 X 4 X 70" CENTER DECK SUPPORT ON THESE MARKS AND PUSH THE CENTER DECK SUPPORT FLUSH 

TO THE BOTTOM SIDE OF THE DECK BOARDS.
5: USING TWO 2-1/2" WOOD SCREWS, INSTALL THE 2 X 4 X 70" CENTER DECK SUPPORT THROUGH THE OUTSIDE OF 

THE 2 X 6, AND INTO THE END OF THE CENTER DECK SUPPORT. REPEAT THIS STEP ON THE OPPOSITE END OF THE 

FORT.

USE 2-1/2" WOOD SCREWS IN THESE LOCATIONS 

ON EACH SIDE.

CENTER DECK SUPPORT

2 X 4 X 70"

2" WOOD SCREW

52

Содержание Pioneer Peak 1500DW





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды