golmar NEXA Series Скачать руководство пользователя страница 3

Страница: 3 / 146

AUDIO AND VIDEO DOOR ENTRY SYSTEM WITH NEXA CODED PANEL

SYSTEM CHARACTERISTICS

Microprocessed devices with simplified wiring (bus without call wires):

Audio door entry system with 4 common wires.

Video door entry system with 3 common wires plus coaxial cable

Video door entry system with 4 common wires plus twisted pair

Video door entry system with simplified wiring (non-polarised 2-wire bus Gtwin).

Can be combined with “Nexa Modular” and “Inox Modular” door panels

Configuration programmable using a numeric keypad, PC or tablet. USB or wireless connection (module

CD-NEXA/BT required)

2 potential-free relay outputs (NO, C, NC), 1 lock release relay (CV1, CV2) and digital panic output (to alarm control

centre).

Residents list with up to 1,990 contacts

4, 5 or 6 digit programmable codes

Possibility of using the same user pin for the different relays and digital panic output

Relays 1 and 2 with three potential-free contacts (NO, C, NC), configurable by programming in stable or impulse mode

(maximum load: 18Vac/1A 18VA or 24Vdc/0.75 A 18 W).

Impulse mode activation time programmable from 1 to 99 seconds for each relay and digital panic output.

Lock activation time programmable from 3 to 15 minutes.

Wrong code lock programmable for 3 to 9 attempts and at an interval also programmable from 1 to 15 minutes

Up to 3 inputs for relay 1 external activation button (PL1), relay 2 (PL2) and relay 3 (AP).

OLED display (module N3403/AL or NX3403) and front LEDs to show operating status.

Содержание NEXA Series



















































































































































Результаты поиска

Содержание NEXA Series

Отзывы:

Похожие инструкции для NEXA Series

Бренды по названию

Популярные бренды

golmar NEXA Series, Руководство пользователя

Результаты поиска

Содержание NEXA Series

Отзывы:

Похожие инструкции для NEXA Series

Бренды по названию

Популярные бренды