golmar NEXA Series Скачать руководство пользователя страница 133

Страница: 133 / 146

PROGRAMMING THE DOOR PANEL

133

MODIFY
DELETE

DELETE ALL

INSERT

Enables all entries in the RESIDENT LIST to be deleted. Press

to start the

process. When the message CONFIRM DELETION appears, press

con

ﬁ

rm or

to cancel the process.

Note: Once entries are deleted, they cannot be recovered.

DELETE
DELETE ALL

SEND BOOKMARK

MODIFY

Enables resident list data to be sent to another door panel or the guard unit of

the same system. Before sending, the receiving device must be in reception
mode (see following section).

To start sending, press

. The screen will show the message SENDING

…

and the sending record number.

After this operation, the devices will exit the con

ﬁ

guration menu.

SENDING…

0056/0100

DELETE ALL
SEND BOOKMARK

RECEIVE BOOKMARK

DELETE

RECEIVING…

0056

Enables resident list information to be received from another door panel or

the guard unit of the same system.

To start receiving, press

and set the sending device to sending mode (see

above). The screen will show the message RECEIVING

…

and the reception

record number.

Before reception, the device deletes the contents of the resident list and

displays the message DELETING

…

After transfer, the devices will exit the con

ﬁ

guration menu.

IMPORTANT:

The transfer of entries can only be performed between two points.

DO NOT

set more than one device to reception or sending mode.

During transmission, it is normal for other devices connected to the system to enter random

operation (call reception, door opening, etc.).

TX RFID

RX RFID

BUS TEST

RECEIVE BOOKMARK

Enables a test of the monitors associated with the contacts in the resident

list to be carried out. Look through the resident list and check that the
associated monitor is connected and ready to receive calls.

To start the process, press

R sident list menu:

Continued from previous page

AUDIO AND VIDEO DOOR ENTRY SYSTEM - CODED PANEL WITH DISPLAY

SEND BOOKMARK
RECEIVE BOOKMARK

TX RFID

DELETE ALL

RECEIVE BOOKMARK
TX RFID

RX RFID

SEND BOOKMARK

To 'RFID' option, see manual "TCODE/CA NFC NEXA".

Содержание NEXA Series



















































































































































Результаты поиска

Содержание NEXA Series

Отзывы:

Похожие инструкции для NEXA Series

Бренды по названию

Популярные бренды

golmar NEXA Series, Руководство пользователя

Результаты поиска

Содержание NEXA Series

Отзывы:

Похожие инструкции для NEXA Series

Бренды по названию

Популярные бренды