background image

6-01. Troubleshooting Procedures (Continued)

Problem

Probable Cause

Corrective Action

Appliance will not heat ...

• Hood Powered light

ON

FILTER MISSING

light

ON

APPLIANCE POWERED

light

OFF

a. Baffle Filter missing or not

properly installed

Install Baffle Filter or check
alignment.

b. Baffle Filter missing or not

properly installed

Install Charcoal Filter or check
alignment.

c. Filter switch(es) faulty

Replace Filter switch(es).

Appliance will not heat ...

• Hood Powered light

ON

FILTER CLOGGED

light

ON

APPLIANCE POWERED

light

OFF

• Continuous tone alarm sounding

a. Baffle or Charcoal Filter

clogged

Replace Charcoal Filter or clean
Baffle Filter.

b. Hood exhaust outlet

excessively block

Confirm exhaust is clear and min.
clearance requirement is met.

c. Vacuum Switch (clogged filter

sensor) is out of adjustment

Have vacuum switch adjusted.

d. Kinked or blocked vacuum

line

Remove vacuum line kinks or
blockage.

e. Fan running slow or blades

are loaded with grease film

Check voltage and inspect blower,
clean if needed

Appliance will not heat ...

• Hood Power light

ON

CHECK

and/or

WASH

LED’s

ON

APPLIANCE POWERED

light

OFF

• Intermittent tone (beeping) alarm

sounding

a. EAC is shorted

Repair or replace EAC cell.

b. EAC excessively dirty

Clean EAC cell.

c. EAC power supply is faulty

Replace EAC power supply.

d. EAC wires shorted to ground

Check voltage, check wiring.

e. Contact Plate is faulty

Replace Contact Plate.

f. EAC driver board is faulty

Replace EAC driver module.

g. Too many EAC ionizer wires

broken or missing

Replace ionizer wires.

h. EAC cell is not installed

Install clean EAC cell.

Troubleshooting

Model: OVH-10-C

36

Содержание OVH-10-C























































Отзывы: