GILES FSH-2-PH Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 66

background image

38

Cleaning & Maintenance

FSH

−

2

−

PH

5.01.2

E.A.C. Filter Cell Cleaning

−

continued

4. Carefully move cell to sink and rinse thoroughly, using hot water spray.

Rinse ONLY, DO NOT scrub

with brushes.

5. Stand cell upright on end on a drain board, w/contact plate up ... allow it to drain and air dry

overnight. The cell must be completely dry before being replaced in hood unit. If desired, a small
electric fan can be used to blow across the cell to help expedite drying.

6. Before replacing cell in the hood, inspect for broken/missing ionizer wires and bent fins. Broken

or missing wires need to be replaced promptly. Bent fins may be straightened by hand so that no
fins are touching adjacent fins.

IMPORTANT! ONLY Simple Green® Crystal Foaming Cleaner/Degreaser is recommended by GILES for cleaning the
E.A.C. cell in this manner. Other spray cleaners have not been evaluated and may contain corrosive ingredients that
may damage the metal, causing cell to fail or not perform properly. Such damages are not covered by the factory
warranty.

Corporate approved product for the soak method of cleaning the collector cell is

EcoLab

LIQUID STORM™

which must

be diluted in clean water at the rate of three (3) packets per 6 gals

(1:2 ra

ti

o)

.

Giles

factory

recommended product for the soaking method is

Simple Green® Pro

‐

HD,

a readily available, biodegradable,

non

toxic degreasing cleaner that is safe for use on aluminum. It performs well to clean the cell when diluted at a

1:12

ratio

(e.g. 1/2 gal. cleaner to 6 gals water)

.

DO NOT use DISHWASHING DETERGENTS other than these approved cleaners as they may contain ingredients that can
damage the metal components, causing failure or unsatisfactory performance. Such damages are not covered by the

factory warranty.

1. Cleaning with this method requires a suitable, leakproof container, such as a trash bin, recycle bin,

plastic tote, or a

Giles soaking tank

. The container must be large enough to hold the cell long with

enough cleaning solution for it to be completely submerged, either standing on end, on
edge, or lying flat.

IMPORTANT! Giles has adopted the spray cleaner method for cleaning the collector cell as
the “best practice” and has subsequently discontinued providing a Giles Soaking Tank with
its ventless hood products, however the tank is still available for separate purchase ... Item
No. 91123

.

2A. Place cell into suitable container and fill with fresh water to a level that covers the cell. Measure water while filling

and note the quantity.

• With

LIQUID STORM™:

add product in

ra

ti

o of 1:2

to water ...

e.g. 8 gals of water requires (4) packets of

product

... stir to mix.

• With

Simple Green® Pro

‐

HD:

add product in

ratio of 1:12

to the water ...

e.g. 8 gals of water requires .67 gals (2

qts+21 ozs) of degreaser

... stir to mix.

2B. Using a

Giles Soak Tank ...

•

With

LIQUID STORM™:

pour

three (3) packets

of product into the tank and

fi

ll with clean water to the full

line indicated by “X”

...

stir to mix.

• With

Simple Green® Pro

‐

HD:

pour

1/2 gal

of product into the tank

and

fi

ll with clean water to the full line

indicated by “X”

...

stir to mix.

B. Alternate Cleaning Method

−

Soaking

Continued on Next Page

«
...
46
47
48
49
50
...
»

Содержание FSH-2-PH



































































Отзывы:

Нет отзывов

Похожие инструкции для FSH-2-PH

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Jackco Страницы: 6

Бренд: Hantek Страницы: 124

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: PA Страницы: 28

Бренд: CAB Страницы: 30

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: Thoratec Страницы: 8

Combination EC Series

Бренд: Eastey Страницы: 81

2 - Person Chest Press

Бренд: Paris Страницы: 5

Бренд: Danfoss Страницы: 18

SelfCooking Center Combi Master

Бренд: Rational Страницы: 40

Бренд: X Training Equipment Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды