manualshive.com logo in svg

GILBARCO VEEDER-ROOT Applause Media System, Инструкция по установке, обслуживанию и ремонту

Поделиться
Скачать
GILBARCO VEEDER-ROOT Applause Media System Скачать руководство пользователя страница 57

MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Page 5-19

Troubleshooting

Service

Applause Media System Related Problems

Following table lists several Applause Media System-related problems with suggested 
solutions:

Symptom

Probable Cause

Suggested Solutions

Cannot connect to 
Gilbarco Site Server’s 
web configuration 
screen (with the laptop 
connected).

The Gilbarco Site Server has not 
completed its startup process.

Wait for the server to power-up and successfully boot. Then, from your 
laptop, ping the IP address to which you are attempting to connect.

You may have a cable problem.

• If your laptop is connected directly to the Gilbarco Site Server you must 

use a crossover CAT-5 cable.

• If your laptop and the Gilbarco Site Server are connected through an 

Ethernet (WAN) hub, you must use a standard CAT-5 cable to the hub.

Gilbarco Site Server 
cannot connect to the 
Control Center.

Faulty Internet connection.

• If you do not have a dial-up connection:

- Attempt to ping the default gateway IP address from the Gilbarco 

Site Server. If not successful, you have a cable problem between the 
Gilbarco Site Server and the default gateway.

- Check cable connections.
- Check cable for damage.

This can happen if you are using DHCP, and your DHCP server is not 
providing a valid Domain Name System (DNS) server for the Gilbarco 
Site Server to use. Use a static IP and select a valid DNS server.

Change in the connectivity status (for 
example, customer decided to change 
the internet service provider).

• Phone line down.
• Server lock up.
• No scheduled content.

Promotions are not 
being displayed on any 
dispensers.

Cable problem between the Gilbarco 
Site Server and the dispenser network.

Attempt to ping one or more of the fueling dispensers IP address(es).
• If this is not successful, there is a cable problem between the Gilbarco 

Site Server and the dispenser network.

- Check cable connections.
- Check cable for damage.

• If this is successful on one of the dispensers, one or more of the other 

dispensers are misconfigured. Attempt to ping other dispensers to 
determine if a particular dispenser is misconfigured.

Promotions are not 
being displayed on one 
specific dispenser.

Cable problem between the Gilbarco 
Site Server and the specific dispenser.

Attempt to ping the fueling dispensers IP address.
• If not successful, do the following:

- Check cable connections.
- Check cable for damage.

• If successful, do the following:

- Reboot the dispenser, if it still does not display content.
- After reboot, if the dispenser still does not display content, examine 

the “merch_error.log” and “merch_event.log” log files on the Gilbarco 
Site Server to see if there are any indications of a problem with the 
dispenser in question.

Содержание Applause Media System







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды