GILBARCO VEEDER-ROOT Applause Media System Скачать руководство пользователя

Страница: 42 / 102

Service

Troubleshooting

Page 5-4 MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Site Server Cannot Connect and Receive Content for Gilbarco Control
Center

To check that connection is set up to the site server, proceed as follows:

• Check connections.
• Check programming.
• Ensure that the Control Center host name, location ID, and so on, are programmed

correctly.

Gilbarco Site Server Software Not Loading

To check that Gilbarco Site Server software loads, proceed as follows:

Note: Connect a keyboard and monitor to the Gilbarco Site Server when you perform this

procedure. Also, ensure that the correct software disk is used.

Warmstart the Gilbarco Site Server holding down

Delete

on the keyboard while the server

power backs up. The Basic Input/Output System (BIOS) Set screen appears.

Select

ADVANCED BIOS features

Scroll down to “First Boot Device”. Ensure that it is set to “CDROM”.

Ensure that the second boot device is set to “Hard Disk”.

If the first and second boot devices are not correct, proceed to one of the following sections



(as applicable):

•

“Configuring BIOS on Gilbarco Site Server [Silver Server (PA03580001)]”

•

“Configuring BIOS on Gilbarco Site Server [Black Server (PA03580002)]”

page 5-11

•

“Configuring BIOS on Gilbarco Site Server [Black Minitower and 1U Chassis
(PA03580003X)]”

page 5-16

Configuring BIOS on Gilbarco Site Server [Silver Server (PA03580001)]

The BIOS on the Gilbarco Site Server is factory set. Use this configuration procedure
only if the BIOS is lost or corrupted.

CAUTION

Note: The power supply to the Gilbarco Site Server must be maintained in the event of a

power failure. Power connection to a Uninterruptible Power Supply (UPS) is strongly
recommended.

To configure the BIOS in the Gilbarco Site Server, proceed as follows:

Connect the monitor and keyboard to the server.

Power up the server.

Содержание Applause Media System







































































































Результаты поиска

Содержание Applause Media System

Отзывы:

Похожие инструкции для Applause Media System

Бренды по названию

Популярные бренды

GILBARCO VEEDER-ROOT Applause Media System, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание Applause Media System

Отзывы:

Похожие инструкции для Applause Media System

Бренды по названию

Популярные бренды